- 您現在的位置：買賣IC網 > PDF目錄1916 > DS80C410-FNY+ (Maxim Integrated Products)IC MCU 75MHZ 16MB HP 100-LQFP PDF資料下載
參數資料
| 型號： | DS80C410-FNY+ |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 101/102頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC MCU 75MHZ 16MB HP 100-LQFP |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 90 |
| 系列： | 80C |
| 核心處理器： | 8051 |
| 芯體尺寸： | 8-位 |
| 速度： | 75MHz |
| 連通性： | 1 線，CAN，EBI/EMI，以太網，SIO，UART/USART |
| 外圍設備： | 電源故障復位，WDT |
| 輸入/輸出數： | 64 |
| 程序存儲器容量： | 64KB（64K x 8） |
| 程序存儲器類型： | ROM |
| RAM 容量： | 64K x 8 |
| 電壓 - 電源 (Vcc/Vdd)： | 1.62 V ~ 3.6 V |
| 振蕩器型： | 外部 |
| 工作溫度： | -40°C ~ 85°C |
| 封裝/外殼： | 100-LQFP |
| 包裝： | 托盤 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁當前第101頁第102頁
DS80C410/DS80C411 Network Microcontrollers with Ethernet and CAN
98 of 102
Changing the System Clock/Machine Cycle Clock Frequency
The microcontroller incorporates a special locking sequence to ensure “glitch-free” switching of the internal clock
signals. All changes to the CD1, CD0 bits must pass through the 10 (divide-by-4) state. For example, to change
from 00 (frequency multiplier) to 11 (PMM), the software must change the bits in the following sequence: 00b =>
10b => 11b. Attempts to switch between invalid states fail, leaving the CD1, CD0 bits unchanged.
The following sequence must be followed when switching to the frequency multiplier as the internal time source.
This sequence can only be performed when the device is in divide-by-4 operation. The steps must be followed in
this order, although it is possible to have other instructions between them. Any deviation from this order causes the
CD1, CD0 bits to remain unchanged. Switching from frequency multiplier to nonmultiplier mode requires no steps
other than the changing of the CD1, CD0 bits.
1) Ensure that the CD1, CD0 bits are set to 10, and the RGMD (EXIF.2) bit = 0.
2) Clear the crystal multiplier enable (CTM) bit.
3) Set the 4X/2X bit to the appropriate state.
4) Set the CTM bit.
5) Poll the CKRDY bit (EXIF.3), waiting until it is set to 1. This takes approximately 65,536 cycles of the external
crystal or clock source.
6) Set CD1, CD0 to 00. The frequency multiplier is engaged on the machine cycle following the write to these bits.
Figure 21. System Clock Control Diagram
Switchback
As an alternative to software changing the CD1 and CD0 clock control bits to exit PMM, the microcontroller
provides hardware alternatives for automatic switchback to standard speed (divide-by-4) operation. When enabled,
the switchback feature allows serial ports and interrupts to automatically switch back from divide-by-1024 (PMM) to
divide-by-4 (standard speed) operation. This feature makes it very convenient to use the PMM in real-time
applications.
The switchback feature is enabled by setting the SFR bit SWB (PMR.5) to a 1. Once it is enabled, and PMM is
selected, two possible events can cause an automatic switchback to divide-by-4 mode. First, if an external interrupt
occurs and is acknowledged, the system clock reverts from PMM to divide-by-4 mode. For example, if INT0 is
enabled and the CPU is not servicing a higher priority interrupt, then switchback occurs on INT0. However, if INT0
is not enabled or the CPU is servicing a higher priority interrupt, then activity on INT0 does not cause switchback to
occur.
A switchback can also occur when an enabled UART detects the start bit, indicating the beginning of an incoming
serial character or when the SBUF register is loaded initiating a serial transmission. Note that a serial character’s
start bit does not generate an interrupt. The interrupt occurs only on reception of a complete serial word. The
automatic switchback on detection of a start bit allows hardware to return to divide-by-4 operation (and the correct
baud rate) in time for a proper serial reception or transmission.
相關PDF資料 |
PDF描述 |
|---|---|
| DS8102+ | IC MODULATOR/DECODER 16-TSSOP |
| DS8113-JNG+ | IC INTERFACE SMART CARD 28-TSSOP |
| DS8313-RRX+ | IC INTERFACE SMART CARD 28-SOIC |
| DS8500-JND+T&R | IC MODEM HART SGL 3.6V 20-TQFN |
| DS87C520-ENL | IC MCU EPROM/ROM 33MH IND 44TQFP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS80C410-FNY+ | 功能描述:8位微控制器 -MCU Network MCU w/Ethernet & CAN RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| DS80C411 | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Network Microcontrollers with Ethernet and CAN |
| DS80C411-FNY | 功能描述:8位微控制器 -MCU Network MCU w/Ethernet & CAN RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| DS80C411-FNY+ | 功能描述:8位微控制器 -MCU Network MCU w/Ethernet & CAN RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| DS80CH11 | 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:System Energy Manager |
發布緊急采購，3分鐘左右您將得到回復。