參數資料
型號： DS80C410-FNY+
廠商： Maxim Integrated Products
文件頁數： 51/102頁
文件大小： 0K
描述： IC MCU 75MHZ 16MB HP 100-LQFP
產品培訓模塊： Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
標準包裝： 90
系列： 80C
核心處理器： 8051
芯體尺寸： 8-位
速度： 75MHz
連通性： 1 線，CAN，EBI/EMI，以太網，SIO，UART/USART
外圍設備： 電源故障復位，WDT
輸入/輸出數： 64
程序存儲器容量： 64KB（64K x 8）
程序存儲器類型： ROM
RAM 容量： 64K x 8
電壓 - 電源 (Vcc/Vdd)： 1.62 V ~ 3.6 V
振蕩器型： 外部
工作溫度： -40°C ~ 85°C
封裝/外殼： 100-LQFP
包裝： 托盤
DS80C410/DS80C411 Network Microcontrollers with Ethernet and CAN
52 of 102
Table 11. Arithmetic Accelerator Sequencing
DIVIDE (32/16 or 16/16)
MULTIPLY (16 x 16)
Load MA with dividend LSB.
Load MA with dividend LSB + 1*.
Load MA with dividend LSB + 2*.
Load MA with dividend MSB.
Load MB with divisor LSB.
Load MB with divisor MSB.
Poll the MST bit until cleared.
(9 machine cycles for 32-bit numerator)
(6 machine cycles for 16-bit numerator)
Read MA to retrieve the quotient MSB.
Read MA to retrieve the quotient LSB + 2*
Read MA to retrieve the quotient LSB + 1*
Read MA to retrieve the quotient LSB.
Read MB to retrieve the remainder MSB.
Read MB to retrieve the remainder LSB.
Load MB with multiplier LSB.
Load MB with multiplier MSB.
Load MA with multiplicand LSB.
Load MA with multiplicand MSB.
Poll the MST bit until cleared (6 machine cycles).
Read MA for product MSB.
Read MA for product LSB + 2.
Read MA for product LSB + 1.
Read MA for product LSB.
SHIFT RIGHT/LEFT
NORMALIZE
Load MA with data LSB.
Load MA with data LSB + 1.
Load MA with data LSB + 2.
Load MA with data MSB.
Configure MCNT0/MCNT1 registers as required.
Poll the MST bit until cleared (9 machine cycles).
Read MA for result MSB.
Read MA for result LSB + 2.
Read MA for result LSB + 1.
Read MA for result LSB.
Load MA with data LSB.
Load MA with data LSB + 1.
Load MA with data LSB + 2.
Load MA with data MSB.
Configure MCNT0.4–0 = 00000b.
Poll the MST bit until cleared (9 machine cycles).
Read MA for mantissa MSB.
Read MA for mantissa LSB + 2.
Read MA for mantissa LSB + 1.
Read MA for mantissa LSB.
Read MCNT0.4–MCNT0.0 for exponent.
*Not performed for 16-bit numerator.
40-Bit Accumulator
The accelerator also incorporates an automatic accumulator function, permitting the implementation of multiply-
and-accumulate and divide-and-accumulate functions without any additional delay. Each time the accelerator is
used for a multiply or divide operation, the result is transparently added to a 40-bit accumulator. This can greatly
increase speed of DSP and other high-level math operations.
The accumulator can be accessed any time the multiply/accumulate status flag (MCNT1;D2h) is cleared. The
accumulator is initialized by performing five writes to the multiplier C register (MC;D5h), LSB first. The 40-bit
accumulator can be read by performing five reads of the multiplier C register, MSB first.
Ethernet Controller
The DS80C410 incorporates a 10/100Mbps Ethernet controller, which supports the protocol requirements for
operating an Ethernet/IEEE 802.3-compliant PHY device. It provides receive, transmit, and flow control
mechanisms through a media-independent interface (MII), which includes a serial management bus for configuring
external PHY devices. The MII can be configured to operate in half-duplex or full-duplex mode at either 10Mbps or
100Mbps, or can support 10Mbps ENDEC mode operation. The system clock (external clock source after internal
multiplication or division) must be a minimum of 25MHz for use of the Ethernet 100Mbps mode.
For half-duplex mode operation, the DS80C410 shares the Ethernet physical media with other stations on the
network. The DS80C410 follows the IEEE 802.3 carrier-sense multiple-access with collision detection (CSMA/CD)
method for accessing the physical media. The MAC waits until the physical carrier is idle before attempting a
transmission. Having multiple stations on the network results in the possibility of transmissions from different
stations colliding. When a collision is detected, the MAC waits some number of time slots (according to an internal
back-off timer) before attempting retransmission. Unless instructed otherwise, the MAC automatically attempts to
retransmit collided frames up to 16 times before aborting the transmit frame. As a means of flow control when
receiving data, the MAC uses a back-pressure scheme, transmitting a jamming signal to force collisions on
相關PDF資料
PDF描述
DS8102+ IC MODULATOR/DECODER 16-TSSOP
DS8113-JNG+ IC INTERFACE SMART CARD 28-TSSOP
DS8313-RRX+ IC INTERFACE SMART CARD 28-SOIC
DS8500-JND+T&R IC MODEM HART SGL 3.6V 20-TQFN
DS87C520-ENL IC MCU EPROM/ROM 33MH IND 44TQFP
相關代理商/技術參數
參數描述
DS80C410-FNY+ 功能描述:8位微控制器 -MCU Network MCU w/Ethernet & CAN RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
DS80C411 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Network Microcontrollers with Ethernet and CAN
DS80C411-FNY 功能描述:8位微控制器 -MCU Network MCU w/Ethernet & CAN RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
DS80C411-FNY+ 功能描述:8位微控制器 -MCU Network MCU w/Ethernet & CAN RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
DS80CH11 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:System Energy Manager
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*