參數資料
型號： ENC424J600T-I/ML
廠商： Microchip Technology
文件頁數： 87/168頁
文件大小： 0K
描述： IC ETHERNET CTRLR W/SPI 44-QFN
視頻文件： Fast 100 Mbps Ethernet PICtail Plus Overview
標準包裝： 1,600
控制器類型： 以太網控制器（IEEE 802.3）
接口： SPI
電源電壓： 3 V ~ 3.6 V
電流 - 電源： 96mA
工作溫度： -40°C ~ 85°C
安裝類型： 表面貼裝
封裝/外殼： 44-VQFN 裸露焊盤
供應商設備封裝： 44-QFN（8x8）
包裝： 帶卷 (TR)
配用： AC164132-ND - BOARD DAUGHTER PICTAIL ETHERNET
2007 Microchip Technology Inc.
DS21993C-page 23
PIC16CR7X
2.2.2.5
PIR1 Register
The PIR1 register contains the individual flag bits for
the peripheral interrupts.
Note:
Interrupt flag bits are set when an interrupt
condition occurs, regardless of the state of
its corresponding enable bit or the global
enable bit, GIE (INTCON<7>). User soft-
ware should ensure the appropriate interrupt
bits are clear prior to enabling an interrupt.
REGISTER 2-5:
PIR1: (ADDRESS 0Ch)
R/W-0
R-0
R/W-0
PSPIF(1)
ADIF
RCIF
TXIF
SSPIF
CCP1IF
TMR2IF
TMR1IF
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 7
PSPIF(1): Parallel Slave Port Read/Write Interrupt Flag bit
1
= A read or a write operation has taken place (must be cleared in software)
0
= No read or write has occurred
bit 6
ADIF: A/D Converter Interrupt Flag bit
1
= An A/D conversion is completed (must be cleared in software)
0
= The A/D conversion is not complete
bit 5
RCIF: USART Receive Interrupt Flag bit
1
= The USART receive buffer is full
0
= The USART receive buffer is empty
bit 4
TXIF: USART Transmit Interrupt Flag bit
1
= The USART transmit buffer is empty
0
= The USART transmit buffer is full
bit 3
SSPIF: Synchronous Serial Port (SSP) Interrupt Flag
1
= The SSP interrupt condition has occurred, and must be cleared in software before
returning from the Interrupt Service Routine. The conditions that will set this bit are:
SPI
A transmission/reception has taken place.
I2C Slave
A transmission/reception has taken place.
I2C Master
A transmission/reception has taken place.
The initiated Start condition was completed by the SSP module.
The initiated Stop condition was completed by the SSP module.
The initiated Restart condition was completed by the SSP module.
The initiated Acknowledge condition was completed by the SSP module.
A Start condition occurred while the SSP module was Idle (multi-master system).
A Stop condition occurred while the SSP module was Idle (multi-master system).
0
= No SSP interrupt condition has occurred
bit 2
CCP1IF: CCP1 Interrupt Flag bit
Capture mode:
1
= A TMR1 register capture occurred (must be cleared in software)
0
= No TMR1 register capture occurred
Compare mode:
1
= A TMR1 register compare match occurred (must be cleared in software)
0
= No TMR1 register compare match occurred
PWM mode:
Unused in this mode
bit 1
TMR2IF: TMR2 to PR2 Match Interrupt Flag bit
1
= TMR2 to PR2 match occurred (must be cleared in software)
0
= No TMR2 to PR2 match occurred
bit 0
TMR1IF: TMR1 Overflow Interrupt Flag bit
1
= TMR1 register overflowed (must be cleared in software)
0
= TMR1 register did not overflow
Note
1:
PSPIF is reserved on 28-pin devices; always maintain this bit clear.
相關PDF資料
PDF描述
PIC16F677-E/P IC PIC MCU FLASH 2KX14 20DIP
MCP2155-I/P IC IRDA PROTOCOL CTRLR 18DIP
MCP2150T-I/SS IC IRDA STD CONTROLLER 20SSOP
MCP2155T-I/SO IC IRDA PROTOCOL CONTRLR 18-SOIC
PIC18F25J10T-I/SS IC PIC MCU FLASH 16KX16 28SSOP
相關代理商/技術參數
參數描述
ENC424J600T-IPT 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:Stand-Alone 10/100 Ethernet Controller with SPI or Parallel Interface
ENC431D05A 制造商:未知廠家 制造商全稱:未知廠家 功能描述:
ENC431D-05A 制造商:未知廠家 制造商全稱:未知廠家 功能描述:STD MOV
ENC431D07A 制造商:未知廠家 制造商全稱:未知廠家 功能描述:
ENC431D-07A 制造商:未知廠家 制造商全稱:未知廠家 功能描述:STD MOV
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*