- 您現在的位置：買賣IC網 > PDF目錄17049 > EVAL-AD7719EBZ (Analog Devices Inc)BOARD EVALUATION FOR AD7719 PDF資料下載
參數資料
| 型號： | EVAL-AD7719EBZ |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 32/40頁 |
| 文件大?。?/td> | 0K |
| 描述： | BOARD EVALUATION FOR AD7719 |
| 標準包裝： | 1 |
| ADC 的數量： | 2 |
| 位數： | 16，24 |
| 采樣率（每秒）： | 105 |
| 數據接口： | 串行 |
| 輸入范圍： | 2 Vpp |
| 在以下條件下的電源（標準）： | 4.85mW @ 105SPS |
| 工作溫度： | -40°C ~ 85°C |
| 已用 IC / 零件： | AD7719 |
| 已供物品： | 板 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁當前第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁
REV. A
AD7719
–38–
In this 3-wire configuration, the lead resistances will result in
errors if only one current source is used because the 200 A will
flow through RL1, developing a voltage error between AIN1 and
AIN2. In the scheme outlined below, the second RTD current
source is used to compensate for the error introduced by the
200 A flowing through RL1. The second RTD current flows
through RL2. Assuming RL1 and RL2 are equal (the leads
would normally be of the same material and of equal length),
and IOUT1 and IOUT2 match, the error voltage across RL2
equals the error voltage across RL1, and no error voltage is
developed between AIN1 and AIN2. Twice the voltage is
developed across RL3, but since this is a common-mode voltage,
it will not introduce errors. RCM is included so the current
flowing through the combination of RL3 and RCM develops enough
voltage that the analog input voltage seen by the AD7719 is
within the common-mode range of the ADC. The reference
voltage for the AD7719 is also generated using one of these
matched current sources. This reference voltage is developed
across the 12.5 k
resistor as shown, and applied to the differential
reference inputs of the AD7719. This scheme ensures that the analog
input voltage span remains ratiometric to the reference voltage.
Any errors in the analog input voltage due to the temperature drift
of the RTD current source is compensated for by the variation
in the reference voltage. The typical drift matching between the
two RTD current sources is less than 1 ppm/°C. The voltage on
either IOUT pin can go to within 0.6 V of the AVDD supply.
Smart Transmitters
Smart transmitters are another key design-in area for the AD7719.
The dual
Σ- converter, single-supply operation, 3-wire interface
capabilities, and small package size are all of benefit in smart
transmitters. Here, the entire smart transmitter must operate
from the 4 to 20 mA loop. Tolerances in the loop mean that the
amount of current available to power the transmitter is as low as
3.5 mA. Figure 24 shows a block diagram of a smart transmitter,
which includes the AD7719.
Not shown in Figure 24 is the isolated power source required to
power the front end. The advantages of the AD7719 in these
applications is the dual-channel operation, meaning that the
user does not have to interrupt the main channel when measur-
ing secondary variables, and therefore does not have the latency
associated with the settling times of the digital filter. The fact
that the AD7719 is factory-calibrated means that in the majority
of applications, the user will not have to perform any field cali-
bration given the excellent offset and gain drift performance of
the device as a result of the signal chain chopping employed in
the signal chain.
MICROCONTROLLER
REF OUT2
REF IN
10 F
0.1 F
AVDD
DVDD
AIN1
AIN2
CS
DOUT
SCLK
DIN
DGND
AGND
AIN5
AIN5 COM
REFIN2
REFIN(+)
REFIN(–)
0.1 F
REF OUT1
CLOCK
LATCH
DATA
4.7 F
COM
C1
C2
C3
VCC
GND
AD7719
AD421
BOOST VCC
LV
0.01 F
1k
1000pF
LOOP
POWER
10 F
3.3V
1.25V
DN25D
0.01 F
LOOP
RTN
COMP
DRIVE
MAIN
VARIABLES
SECONDARY
VARIABLES
AIN3
AIN4
Figure 24. Smart Transmitter Employing the AD7719
相關PDF資料 |
PDF描述 |
|---|---|
| EVAL-AD7266EDZ | BOARD EVAL FOR AD7266 A/D CONV |
| GCM22DCSH | CONN EDGECARD 44POS DIP .156 SLD |
| 0982660859 | CBL 17POS 0.5MM JMPR TYPE A 3" |
| 0210490326 | CABLE JUMPER 1.25MM .076M 26POS |
| MAX5138EVKIT+ | EVALUATION KIT FOR MAX5138 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| EVAL-AD7721CB | 制造商:Analog Devices 功能描述:EVALUATION BOARD FOR SINGLE SUPPLY, 12/16-BIT 312.5/468.75 KHZ SEGMA-DELTA ADC 制造商:Analog Devices 功能描述:EVALUATION BOARD - Bulk |
| EVAL-AD7722CB | 制造商:Analog Devices 功能描述:EVALUATION CONTROL BOARD I.C. - Bulk |
| EVAL-AD7722CBZ | 功能描述:BOARD EVALUATION FOR AD7722CBZ RoHS:是 類別:編程器，開發系統 >> 評估板 - 模數轉換器 (ADC) 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- ADC 的數量:1 位數:12 采樣率（每秒）:94.4k 數據接口:USB 輸入范圍:±VREF/2 在以下條件下的電源（標準）:- 工作溫度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，軟件 |
| EVAL-AD7723CB | 制造商:Analog Devices 功能描述:EVALUATION CONTROL BOARD I.C. - Bulk |
| EVAL-AD7723CBZ | 功能描述:BOARD EVALUATION FOR AD7723 RoHS:是 類別:編程器，開發系統 >> 評估板 - 模數轉換器 (ADC) 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- ADC 的數量:1 位數:12 采樣率（每秒）:94.4k 數據接口:USB 輸入范圍:±VREF/2 在以下條件下的電源（標準）:- 工作溫度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，軟件 |
發布緊急采購，3分鐘左右您將得到回復。