- 您現在的位置：買賣IC網 > PDF目錄17049 > EVAL-AD7719EBZ (Analog Devices Inc)BOARD EVALUATION FOR AD7719 PDF資料下載
參數資料
| 型號： | EVAL-AD7719EBZ |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 39/40頁 |
| 文件大小： | 0K |
| 描述： | BOARD EVALUATION FOR AD7719 |
| 標準包裝： | 1 |
| ADC 的數量： | 2 |
| 位數： | 16，24 |
| 采樣率（每秒）： | 105 |
| 數據接口： | 串行 |
| 輸入范圍： | 2 Vpp |
| 在以下條件下的電源（標準）： | 4.85mW @ 105SPS |
| 工作溫度： | -40°C ~ 85°C |
| 已用 IC / 零件： | AD7719 |
| 已供物品： | 板 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁當前第39頁第40頁
REV. A
AD7719
–8–
DIGITAL INTERFACE
As previously outlined, the AD7719’s programmable functions are
controlled using a set of on-chip registers. Data is written to these
registers via the part’s serial interface; read access to the on-chip
registers is also provided by this interface. All communications to
the part must start with a write operation to the Communications
register. After power-on or
RESET, the device expects a write to
its Communications register. The data written to this register
determines whether the next operation to the part is a read or a
write operation and also determines to which register this read
or write operation occurs. Therefore, write access to any of the
other registers on the part starts with a write operation to the
Communications register followed by a write to the selected
register. A read operation from any other register on the part
(including the output data register) starts with a write operation
to the Communications register followed by a read operation
from the selected register.
The AD7719’s serial interface consists of five signals:
CS, SCLK,
DIN, DOUT, and
RDY. The DIN line is used for transferring
data into the on-chip registers while the DOUT line is used for
accessing data from the on-chip registers. SCLK is the serial
clock input for the device, and all data transfers (either on DIN
or DOUT) take place with respect to this SCLK signal. The
RDY line is used as a status signal to indicate when data is ready
to be read from the AD7719’s data register.
RDY goes low when a
new data-word is available in the output register of either the
main or aux ADCs. It is reset high when a read operation from
the data register is complete. It also goes high prior to the updating
of the output register to indicate when not to read from the device
to ensure that a data read is not attempted while the register is
being updated.
CS is used to select the device. It can be used to
decode the AD7719 in systems where a number of parts are
connected to the serial bus.
Figures 2 and 3 show timing diagrams for interfacing to the
AD7719 with
CS used to decode the part. Figure 3 is for a read
operation from the AD7719’s output shift register while Figure 2
shows a write operation to the input shift register. It is possible
to read the same data twice from the output register even though
the
RDY line returns high after the first read operation. Care must
be taken, however, to ensure that the read operations have been
completed before the next output update is about to take place.
The AD7719 serial interface can operate in 3-wire mode by tying
the
CS input low. In this case, the SCLK, DIN, and DOUT lines
are used to communicate with the AD7719, and the status of
RDY bits (RDY0 and RDY1) can be obtained by interrogating
the STATUS register. This scheme is suitable for interfacing to
microcontrollers. If
CS is required as a decoding signal, it can
be generated from a port bit. For microcontroller interfaces, it is
recommended that the SCLK idles high between data transfers.
The AD7719 can also be operated with
CS used as a frame syn-
chronization signal. This scheme is suitable for DSP interfaces.
In this case, the first bit (MSB) is effectively clocked out by
CS
since
CS would normally occur after the falling edge of SCLK
in DSPs. The SCLK can continue to run between data transfers
provided the timing numbers are obeyed.
t12
t13
t14
t15
t11
t16
MSB
LSB
CS
SCLK
DIN
Figure 2. Write Cycle Timing Diagram
t5
t5A
t4
t6
t3
t9
MSB
LSB
CS
SCLK
t8
t10
t7
t6
DOUT
RDY
Figure 3. Read Cycle Timing Diagram
相關PDF資料 |
PDF描述 |
|---|---|
| EVAL-AD7266EDZ | BOARD EVAL FOR AD7266 A/D CONV |
| GCM22DCSH | CONN EDGECARD 44POS DIP .156 SLD |
| 0982660859 | CBL 17POS 0.5MM JMPR TYPE A 3" |
| 0210490326 | CABLE JUMPER 1.25MM .076M 26POS |
| MAX5138EVKIT+ | EVALUATION KIT FOR MAX5138 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| EVAL-AD7721CB | 制造商:Analog Devices 功能描述:EVALUATION BOARD FOR SINGLE SUPPLY, 12/16-BIT 312.5/468.75 KHZ SEGMA-DELTA ADC 制造商:Analog Devices 功能描述:EVALUATION BOARD - Bulk |
| EVAL-AD7722CB | 制造商:Analog Devices 功能描述:EVALUATION CONTROL BOARD I.C. - Bulk |
| EVAL-AD7722CBZ | 功能描述:BOARD EVALUATION FOR AD7722CBZ RoHS:是 類別:編程器，開發系統 >> 評估板 - 模數轉換器 (ADC) 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- ADC 的數量:1 位數:12 采樣率（每秒）:94.4k 數據接口:USB 輸入范圍:±VREF/2 在以下條件下的電源（標準）:- 工作溫度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，軟件 |
| EVAL-AD7723CB | 制造商:Analog Devices 功能描述:EVALUATION CONTROL BOARD I.C. - Bulk |
| EVAL-AD7723CBZ | 功能描述:BOARD EVALUATION FOR AD7723 RoHS:是 類別:編程器，開發系統 >> 評估板 - 模數轉換器 (ADC) 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- ADC 的數量:1 位數:12 采樣率（每秒）:94.4k 數據接口:USB 輸入范圍:±VREF/2 在以下條件下的電源（標準）:- 工作溫度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，軟件 |
發布緊急采購，3分鐘左右您將得到回復。