- 您現在的位置：買賣IC網 > PDF目錄375864 > FMS7401LEN14 (FAIRCHILD SEMICONDUCTOR CORP) Digital Power Controller PDF資料下載
參數資料
| 型號： | FMS7401LEN14 |
| 廠商： | FAIRCHILD SEMICONDUCTOR CORP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | Digital Power Controller |
| 中文描述： | 8-BIT, EEPROM, 2.04 MHz, MICROCONTROLLER, PDIP14 |
| 封裝： | PLASTIC, DIP-14 |
| 文件頁數： | 45/80頁 |
| 文件大?。?/td> | 1535K |
| 代理商： | FMS7401LEN14 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁當前第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁
PRODUCT SPECIFICATION
FMS7401/7401L
REV. 1.0.2 6/23/04
45
9
The Multi-input Wakeup (MIW) circuit may be used to wake the device from either Halt or Idle Mode
1
with an external event,
generate flags for software monitoring and microcontroller hardware interrupts by any one or all I/O ports (G0–G7). The MIW
circuit is configured using the Wakeup Enable (WKEN), Wakeup Edge (WKEDG), Wakeup Pending (WKPND) and
T0CNTRL memory mapped registers.
2
The WKEN, WKEDG and WKPND are 8-bit registers where each bit corresponds to
an I/O port pin (see
Table 21
). All four registers are initialized to 0x00 upon a system reset.
Multi-input Wakeup Circuit
The PWMOFF output signal may also be programmed as an input of the G6 port MIW circuit. Interrupts may be triggered if
the PWMOFF/G6 input MIW circuit is enabled and configured to trigger its microcontroller hardware interrupt (EDGEI).
Bit 6 (PWMINT) of the DDELAY register, if set to 1, selects the PWMOFF signal in place of its G6 input to the MIW circuit.
Software must then enable the MIW PWMOFF/G6 circuit by setting the WKEN[6] bit. The WKEDG[6] bit must also be
cleared to select the rising edge transitions on the PWMOFF signal as its WKPND[6] bit trigger. Software may monitor the
WKPND[6] flag or enable the MIW hardware interrupt (EDGEI) to help detect when the PWMOFF signal is triggered. Refer
to the
Programmable Comparator Circuit
sections of the datasheet for addition details.
9.1
The Wakeup Enable (WKEN) register individually enables an I/O port’s edge transition to trigger a wakeup/interrupt pending
flag. If the WKEN register bit is 1, the corresponding I/O port’s MIW circuitry (defined by its bit number) is enabled; other-
wise, the port circuitry remains disabled and the pending flag may not be triggered.
MIW Configuration Registers
The Wakeup Edge (WKEDG) register bits are used to program an enabled I/O port’s pending flag to be triggered from either a
rising-/falling-edge transition. If the WKEDG register bit is 1, a falling-edge transition of the enabled I/O port will trigger the
pending flag. If zero, a rising-edge transition of the enabled I/O port will trigger the pending flag.
The MIW circuit shares a single hardware interrupt (EDGEI) among all pending flags and is enabled by the Wakeup Interrupt
enable (WKINTEN) bit of the T0CNTRL register.
2
The WKINTEN bit enables hardware interrupts for the MIW circuit if set
to 1.
3
The Wakeup Pending (WKPND) register contains the pending flags corresponding to each of the I/O port pins. If a WKPND
register bit is 1, the programmed I/O port edge transition has triggered its pending flag. If zero, the flag is not pending and no
transition has occurred from the last pending reset. A pending flag may only be triggered by enabled I/O ports (if its WKEN
register bit is 1). Once a pending flag is triggered, all flags are logically-ORed together to trigger a WAKEOUT if in Halt/Idle
Mode and/or hardware interrupts (if enabled). If software is to re-enter Halt/Idle Mode, all pending flags must be cleared, oth-
erwise the command is ignored. Since all MIW pending flags share a single hardware interrupt, software must take care with
the handling of the pending flags when more than one pending flag is enabled. As long as a MIW pending flag is set, the hard-
ware interrupt will continue to execute software’s MIW interrupt service routine with highest priority until all pending flags are
cleared.
4
Upon exiting Halt/Idle Mode or before leaving software’s MIW interrupt service routine, the RBIT instruction may be used to
clear a particular pending flag. The RBIT instruction takes two instruction clock cycles to complete its execution. In the first
cycle, all eight register bits are automatically read to obtain their most current value. In the second cycle, the bit to be cleared is
given its new value and all bits are then re-written to the register. Using the RBIT instruction to clear an individual pending flag
causes no potential hazards if only one wakeup I/O port is enabled. However, if more than one I/O port is enabled software
may inadvertently clear a recently triggered pending flag if the trigger happened during the second phase of the RBIT instruc-
tion execution. To avoid this condition, the LD instruction must be used to clear a set pending flag. The MIW circuit is
designed such that software may not trigger a pending flag by writing a 1 to a WKPND register bit, it may only be cleared. The
action of writing a 1 to a WKPND register bit holds the current bit value. The action of writing a 0 to a WKPND register bit
clears the bit value. Therefore, the “LD WKPND, #0F7H” instruction will clear the WKPND[3] while all others bits remain the
same.
相關PDF資料 |
PDF描述 |
|---|---|
| FMS7401LVN | Digital Power Controller |
| FMS7401LVN14 | Digital Power Controller |
| FMS7G10US60S | SWTCH ROLLER SPDT 20A SCRW TERM |
| FMS7G10US60 | SWTCH ROLLER SPDT 20A SOLD TERM |
| FMS7G15US60S | SWTCH LEVER SPDT 20A SCREW TERM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| FMS7401LEN14_Q | 功能描述:處理器 - 專門應用 Int Controller for Ballast RoHS:否 制造商:Freescale Semiconductor 類型:Multimedia Applications 核心:ARM Cortex A9 處理器系列:i.MX6 數據總線寬度:32 bit 最大時鐘頻率:1 GHz 指令/數據緩存: 數據 RAM 大小:128 KB 數據 ROM 大小: 工作電源電壓: 最大工作溫度:+ 95 C 安裝風格:SMD/SMT 封裝 / 箱體:MAPBGA-432 |
| FMS7401LVN | 功能描述:處理器 - 專門應用 Int Controller for Ballast RoHS:否 制造商:Freescale Semiconductor 類型:Multimedia Applications 核心:ARM Cortex A9 處理器系列:i.MX6 數據總線寬度:32 bit 最大時鐘頻率:1 GHz 指令/數據緩存: 數據 RAM 大小:128 KB 數據 ROM 大小: 工作電源電壓: 最大工作溫度:+ 95 C 安裝風格:SMD/SMT 封裝 / 箱體:MAPBGA-432 |
| FMS7401LVN14 | 功能描述:8位微控制器 -MCU Int Controller for Ballast RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| FMS7401LVN14_Q | 功能描述:8位微控制器 -MCU Int Controller for Ballast RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| FMS75X6 | 功能描述:MAGENTIC STRIP .75" X 6' RoHS:否 類別:線纜，導線 - 管理 >> 線槽，走線系統 - 附件 系列:- 標準包裝:1 系列:PANDUCT® 附件類型:蓋 - 線管 適用于相關產品:Panduit 導管 H 型 高度:- 寬:4"（101.6mm） 長度:36.0"（914.4mm） 顏色:黑 其它名稱:298-HC4BL36 |
發布緊急采購，3分鐘左右您將得到回復。