- 您現在的位置：買賣IC網 > PDF目錄377496 > INTEL82802AB (Intel Corp.) Firmware Hub (FWH) PDF資料下載
參數資料
| 型號： | INTEL82802AB |
| 廠商： | Intel Corp. |
| 英文描述： | Firmware Hub (FWH) |
| 中文描述： | 固件集線器（固件樞紐） |
| 文件頁數： | 21/53頁 |
| 文件大小： | 471K |
| 代理商： | INTEL82802AB |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁當前第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁
Intel
82802AB/AC Firmware Hub
R
Datasheet
21
4.1.
Read Array Command
Upon initial device power-up and after exit from reset, the device defaults to the read array mode. This
operation can also be initiated by writing the Read Array command. The device remains available for
array reads until another command is written. Once the internal write state machine (WSM) has started a
block erase or program, the device will not recognize the Read Array command until the operation is
completed, unless the operation is suspended via an Erase Suspend or Program Suspend command. The
Read Array command functions independently of the V
PP
voltage.
4.2.
Read Identifier Codes Command
The identifier code operation is initiated by writing the Read Identifier Codes command. Following the
write of the command, the device will read back the (manufacturer and device) ID data from the
addresses shown in the following table. To terminate the read identifier code operation, write another
valid command to the Intel FWH. The Read Identifier Codes command functions independently of the
V
PP
voltage.
Table 4.
Identifier Codes
Code
Address
Data
Manufacturer code
000000
89
Device code
4 Mbit
000001
AD
Device code
8 Mbit
000001
AC
4.3.
Read Status Register Command
The status register may be read to determine when a block erase or program completes, and whether the
operation completed successfully. The status register may be read at any time by writing the Read Status
Register command. After writing this command, all subsequent read operations will return data from the
status register until another valid command is written. The Read Status Register command functions
independently of the V
PP
voltage.
4.4.
Clear Status Register Command
Error flags in the status register can only be set to 1s by the WSM and can only be reset by the Clear
Status Register command. These bits indicate various conditions that may cause failure. The Clear Status
Register command functions independently of the applied V
PP
voltage.
相關PDF資料 |
PDF描述 |
|---|---|
| INTELDX2 | High-Performance 32-Bit Embedded Processor(高性能32位嵌入式處理器) |
| INTELDX4 | Embedded Write-Back Enhanced Processor(32位回復嵌入式增強型處理器) |
| IPS54511 | FULLY PROTECTED HIGH SIDE POWER MOSFET SWITCH |
| IPS5451 | FULLY PROTECTED HIGH SIDE POWER MOSFET SWITCH |
| IPS5451S | FULLY PROTECTED HIGH SIDE POWER MOSFET SWITCH |
相關代理商/技術參數 |
參數描述 |
|---|---|
| INTELLIGENT CHARGER + 4AA | 制造商:Energizer 功能描述:Bulk |
| INTELLI-INCH-LR-STARTER K | 制造商:ALL MOTION 功能描述:Intelli-Inch Stepper & Controller Starter Kit |
| INTELLIPANEL | 制造商:GJD 功能描述:EXTENSION LEAD 8GANG INTELLIPANEL 制造商:GJD 功能描述:EXTENSION LEAD, 8GANG, INTELLIPANEL |
| INTELLIPLUG | 制造商:GLOBAL COMMUNICATIONS 功能描述:ADAPTOR 3WAY INTELLIPLUG |
| INTELLIPROBE 100 | 制造商:Fluke Networks 功能描述:TONE + PROBE KIT |
發布緊急采購，3分鐘左右您將得到回復。
