參數資料
型號： INTEL82802AB
廠商： Intel Corp.
英文描述： Firmware Hub (FWH)
中文描述： 固件集線器（固件樞紐）
文件頁數： 23/53頁
文件大小： 471K
代理商： INTEL82802AB
Intel
82802AB/AC Firmware Hub
R
Datasheet
23
4.7.
Block Erase Suspend Command
The Block Erase Suspend command allows block-erase interruption to read or program data in another
block of memory. Once the block erase process starts, writing the Block Erase Suspend command
requests that the WSM suspend the block erase sequence at a predetermined point in the algorithm. The
device outputs status register data when read after the Block Erase Suspend command is written. Polling
the status register can help determine when the block erase operation was suspended.
After a successful suspend, a Read Array command may be written to read data from a block other than
the suspended block. A Program command sequence may also be issued during erase suspend to program
data in blocks other that the block currently in the erase suspend mode.
The other valid commands while block erase is suspended include Read Status Register and Block Erase
Resume. After a Block Erase Resume command is written, the WSM will continue the block erase
process. V
PP
must remain at V
PPH1/2
(the same V
PP
level initially used for the block erase) while block
erase is suspended. RST# or INIT# must also remain at V
IH
. Block erase cannot resume until program
operations initiated during block erase suspend have completed.
4.8.
Program Suspend Comand
The Program Suspend command allows program interruption to read data in other memory locations.
Once the program process starts, writing the Program Suspend command requests that the WSM suspend
the program sequence at a predetermined point in the algorithm. The device continues to output status
register data when read after the Program Suspend command is written. Polling status register bits will
help determine when the program operation was suspended.
After a successful suspend, a Read Array command can be written to read data from locations other than
that which is suspended. The only other valid commands while program is suspended are Read Status
Register and Program Resume. After Program Resume command is written, the WSM will continue the
programming process. V
PP
must remain at V
PPH1/2
(the same V
PP
level used for program) while in program
suspend mode. RST# or INIT# must also remain at V
IH
.
4.9.
Register Based Locking, General-Purpose Input, and
Random Number Generator Registers
A series of registers are available in the Intel FWH to provide software read- and write-locking and GPI
feedback. Also available are the set of control registers for controlling and gathering random numbers.
These registers are accessible through standard addressable memory space (see the following table).
It is recommended that the GPI pins be in the desired state before FWH4 is brought low for the
beginning of the next bus cycle, and remain in that state until the end of the read.
相關PDF資料
PDF描述
INTELDX2 High-Performance 32-Bit Embedded Processor(高性能32位嵌入式處理器)
INTELDX4 Embedded Write-Back Enhanced Processor(32位回復嵌入式增強型處理器)
IPS54511 FULLY PROTECTED HIGH SIDE POWER MOSFET SWITCH
IPS5451 FULLY PROTECTED HIGH SIDE POWER MOSFET SWITCH
IPS5451S FULLY PROTECTED HIGH SIDE POWER MOSFET SWITCH
相關代理商/技術參數
參數描述
INTELLIGENT CHARGER + 4AA 制造商:Energizer 功能描述:Bulk
INTELLI-INCH-LR-STARTER K 制造商:ALL MOTION 功能描述:Intelli-Inch Stepper & Controller Starter Kit
INTELLIPANEL 制造商:GJD 功能描述:EXTENSION LEAD 8GANG INTELLIPANEL 制造商:GJD 功能描述:EXTENSION LEAD, 8GANG, INTELLIPANEL
INTELLIPLUG 制造商:GLOBAL COMMUNICATIONS 功能描述:ADAPTOR 3WAY INTELLIPLUG
INTELLIPROBE 100 制造商:Fluke Networks 功能描述:TONE + PROBE KIT
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*