s" />
參數資料
型號： IS80C286-20
廠商： Intersil
文件頁數： 24/60頁
文件大?。?/td> 0K
描述： IC CPU 16BIT 5V 20MHZ 68-PLCC
標準包裝： 18
處理器類型： 80C286 16-位
速度： 20MHz
電壓： 5V
安裝類型： 表面貼裝
封裝/外殼： 68-LCC（J 形引線）
供應商設備封裝： 68-PLCC（24.23x24.23）
包裝： 管件
30
Bus Cycle Termination
At maximum transfer rates, the 80C286 bus alternates
between the status and command states. The bus status
signals become inactive after TS so that they may correctly
signal the start of the next bus operation after the completion
of the current cycle. No external indication of TC exists on
the 80C286 local bus. The bus master and bus controller
enter TC directly after TS and continue executing TC cycles
until terminated by the assertion of READY.
READY Operation
The current bus master and 82C288 bus controller terminate
each bus operation simultaneously to achieve maximum bus
operation bandwidth. Both are informed in advance by
READY active (open-collector output from 82C284) which
identifies the last TC cycle of the current bus operation. The
bus master and bus controller must see the same sense of
the READY signal, thereby requiring READY to be synchro-
nous to the system clock.
Synchronous Ready
The 82C284 clock generator provides READY synchroniza-
tion from both synchronous and asynchronous sources (see
Figure 24). The synchronous ready input (SRDY) of the
clock generator is sampled with the falling edge of CLK at
the end of phase 1 of each TC. The state of SRDY is then
broadcast to the bus master and bus controller via the
READY output line.
Asynchronous Ready
Many systems have devices or subsystems that are asyn-
chronous to the system clock. As a result, their ready out-
puts cannot be guaranteed to meet the 82C284 SRDY setup
and hold time requirements. But the 82C284 asynchronous
ready input (ARDY) is designed to accept such signals. The
ARDY input is sampled at the beginning of each TC cycle by
82C284 synchronization logic. This provides one system
CLK cycle time to resolve its value before broadcasting it to
the bus master and bus controller.
ARDY or ARDYEN must be HIGH at the end of TS. ARDY
cannot be used to terminate the bus cycle with no wait
states.
Each ready input of the 82C284 has an enable pin
(SRDYEN and ARDYEN) to select whether the current bus
operation will be terminated by the synchronous or asyn-
chronous ready. Either of the ready inputs may terminate a
bus operation. These enable inputs are active low and have
the same timing as their respective ready inputs. Address
decode logic usually selects whether the current bus opera-
tion should be terminated by ARDY or SRDY.
FIGURE 23. CMDLY CONTROLS THE LEADING EDGE OF COMMAND SIGNAL
TS
TC
TS
TC
READ CYCLE N -1
READ CYCLE N
VALID ADDR N
VALID ADDR (N-1)
A23 - A0
PROC
CLK
S1
S0
ALE
READY
RD
CMDLY
RD
CMDLY
EX1
EX2
φ1
φ2
φ1
φ2
φ1
φ2
φ1
φ2
φ1
φ2
80C286
相關PDF資料
PDF描述
ISL1532IRZ IC LINE DRIVER DUAL 24-QFN
ISL1536IRZ IC LINE DRVR DUAL ADSL2+ 16-QFN
ISL1539AIRZ IC VDSL2 LINE DVR AMP 24QFN
ISL1539IVEZ IC VDSL2 LINE DVR AMP 24HTTSOP
ISL1557AIRZ IC LINE DRIVER DUAL 16-QFN
相關代理商/技術參數
參數描述
IS80C31 制造商:ISSI 制造商全稱:Integrated Silicon Solution, Inc 功能描述:CMOS SINGLE CHIP 8-BIT MICROCONTROLLER
IS80C31-12 制造商:TEMIC 功能描述:MicroController, 8-Bit, 44 Pin, Plastic, PLCC
IS80C31-12PL 制造商:ISSI 制造商全稱:Integrated Silicon Solution, Inc 功能描述:CMOS SINGLE CHIP 8-BIT MICROCONTROLLER
IS80C31-12PLI 制造商:ISSI 制造商全稱:Integrated Silicon Solution, Inc 功能描述:CMOS SINGLE CHIP 8-BIT MICROCONTROLLER
IS80C31-12PQ 制造商:ISSI 制造商全稱:Integrated Silicon Solution, Inc 功能描述:CMOS SINGLE CHIP 8-BIT MICROCONTROLLER
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*