- 您現在的位置：買賣IC網 > PDF目錄45377 > IS83C154TXXX-25D (ATMEL CORP) 8-BIT, MROM, 25 MHz, MICROCONTROLLER, PQCC44 PDF資料下載
參數資料
| 型號： | IS83C154TXXX-25D |
| 廠商： | ATMEL CORP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 8-BIT, MROM, 25 MHz, MICROCONTROLLER, PQCC44 |
| 封裝： | PLASTIC, LCC-44 |
| 文件頁數： | 67/101頁 |
| 文件大?。?/td> | 3398K |
| 代理商： | IS83C154TXXX-25D |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁當前第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁
91
8168C-MCU Wireless-02/10
AT86RF212
6.8 Link Quality Indication (LQI)
6.8.1 Requirements
The IEEE 802.15.4 standard defines the LQI as a characterization of the strength
and/or quality of a received frame. The use of the LQI result by the network or
application layer is not specified in this standard. The LQI value shall be an integer
ranging from 0 to 255, with at least 8 unique values. The minimum and maximum LQI
values (0 and 255) should be associated with the lowest and highest quality compliant
signals, respectively, and LQI values in between should be uniformly distributed
between these two limits.
6.8.2 Implementation
During symbol detection within frame reception, the AT86RF212 uses correlation
results of multiple symbols in order to compute an estimate of the LQI value. This is
motivated by the fact that the mean value of the correlation result is inversely related to
the probability of a detection error.
LQI computation is automatically performed for each received frame, once the SHR has
been detected. LQI values are integers ranging from 0 to 255 as required by the IEEE
802.15.4 standard.
6.8.3 Obtaining the LQI Value
The LQI value is available, once the corresponding frame has been completely
received. This is indicated by the interrupt IRQ_3 (TRX_END). The value can be
obtained by means of a frame buffer read access, see section 4.3.2.
6.8.4 Remarks
The reason for a low LQI value can be twofold: a low signal strength and/or high signal
distortions, e.g. by interference and/or multipath propagation. High LQI values,
however, indicate a sufficient signal strength and low signal distortions.
Note that the LQI value is almost always 255 for scenarios with very low signal
distortions and a signal strength much greater than the sensitivity level. In this case, the
packet error rate tends towards zero and increase of the signal strength, i.e. by
increasing the transmission power, cannot decrease the error rate any further.
Received signal strength indication (RSSI) or energy detection (ED) can be used to
evaluate the signal strength and the link margin.
ZigBee networks often require identification of the “best” routing between two nodes.
LQI and RSSI/ED can be applied, depending on the optimization criteria. If a low frame
error rate (corresponding to a high throughput) is the optimization criteria, then the LQI
value should be taken into consideration. If, however, the target is a low transmission
power, then the RSSI/ED value is also helpful.
Various combinations of LQI and RSSI/ED are possible for routing decisions. As a rule
of thumb, information on RSSI/ED is useful in order to differentiate between links with
high LQI values. However, transmission links with low LQI values should be discarded
for routing decisions, even if the RSSI/ED values are high, since it is merely an
information about the received signal strength, whereas the source can be an interferer.
相關PDF資料 |
PDF描述 |
|---|---|
| IF180C52EXXX-L16:R | 8-BIT, MROM, 16 MHz, MICROCONTROLLER, PQFP44 |
| MQ80C52CXXX-20/883R | 8-BIT, MROM, 20 MHz, MICROCONTROLLER, CQFP44 |
| MJ80C31U-36:D | MICROCONTROLLER |
| R80C52XXX-12SHXXX | 8-BIT, MROM, 12 MHz, MICROCONTROLLER, CQCC44 |
| MQ80C32-12SBR | 8-BIT, 12 MHz, MICROCONTROLLER, CQFP44 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| IS83D | 制造商:IDEC CORPORATION 功能描述:SENS.IND. 2W/F 24-230VAC NO |
| IS83DK | 制造商:IDEC CORPORATION 功能描述:SENS.IND. 2W/F 24-230VAC NO |
| IS83DL | 制造商:IDEC CORPORATION 功能描述:SENS.IND. 2W/F 24-230VAC NO |
| IS83K | 制造商:IDEC CORPORATION 功能描述:SENS.IND. 2W/F 24-230VAC NO |
| IS83L | 制造商:IDEC CORPORATION 功能描述:SENS.IND. 2W/F 24-230VAC NO |
發布緊急采購，3分鐘左右您將得到回復。