- 您現在的位置：買賣IC網 > PDF目錄45377 > IS83C154TXXX-25D (ATMEL CORP) 8-BIT, MROM, 25 MHz, MICROCONTROLLER, PQCC44 PDF資料下載
參數資料
| 型號： | IS83C154TXXX-25D |
| 廠商： | ATMEL CORP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 8-BIT, MROM, 25 MHz, MICROCONTROLLER, PQCC44 |
| 封裝： | PLASTIC, LCC-44 |
| 文件頁數： | 82/101頁 |
| 文件大?。?/td> | 3398K |
| 代理商： | IS83C154TXXX-25D |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁當前第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁
104
Figure 7-4 to Figure 7-8 illustrate typical spectra of the transmitted signals of the
AT86RF212 and do not claim any limits.
Refer to the local authority bodies (FCC, ETSI, etc.) for further details about definition of
power spectral density masks, definition of spurious emission, allowed modulation
bandwidth, transmit power, and its limits.
7.3.4 TX Output Power
The maximum output power of the transmitter is typically 5 dBm in normal mode and 10
dBm in boost mode. The TX output power can be set via register bits TX_PWR (register
0x05, PHY_TX_PWR). The output power of the transmitter can be controlled down to
-11 dBm dB with 1 dB resolution.
To meet the spectral requirements of the European and Chinese bands, it is necessary
to limit the TX power by appropriate setting of TX_PWR, GC_PA (register 0x05,
PHY_TX_PWR), and GC_TX_OFFS (register 0x16, TX_CTRL_0). See Table 7-15 and
Table 7-16 for recommended values.
7.3.5 TX Power Ramping
To optimize the output power spectral density (PSD), individual transmitter blocks are
enabled sequentially. A transmit action is started by either the rising edge of pin
SLP_TR or the command TX_START in register 0x02. One symbol period later the data
transmission begins. During this time period, the PLL settles to the frequency used for
transmission. The PA is enabled prior to the data transmission start. This PA lead time
can be adjusted with the value PA_LT in register 0x16 (RF_CTRL_0). The PA is always
enabled at the lowest gain value corresponding to GC_PA = 0. Then the PA gain is
increased automatically to the value set by GC_PA in register 0x16 (RF_CTRL_0). After
transmission is completed, TX power ramping down is performed in an inverse order.
The control signals associated with TX power ramping are shown in Figure 7-9. In this
example, the transmission is initiated with the rising edge of pin 11 (SLP_TR). The radio
transceiver state changes from PLL_ON to BUSY_TX.
Figure 7-9. TX Power Ramping Example (O-QPSK 250 kbit/s Mode)
Using an external RF front-end (refer to section 9.4), it may be required to adjust the
startup time of the external PA relative to the internal building blocks to optimize the
overall PSD. This can be achieved using register bits PA_LT (register 0x16,
RF_CTRL_0).
AT86RF212
8168C-MCU Wireless-02/10
相關PDF資料 |
PDF描述 |
|---|---|
| IF180C52EXXX-L16:R | 8-BIT, MROM, 16 MHz, MICROCONTROLLER, PQFP44 |
| MQ80C52CXXX-20/883R | 8-BIT, MROM, 20 MHz, MICROCONTROLLER, CQFP44 |
| MJ80C31U-36:D | MICROCONTROLLER |
| R80C52XXX-12SHXXX | 8-BIT, MROM, 12 MHz, MICROCONTROLLER, CQCC44 |
| MQ80C32-12SBR | 8-BIT, 12 MHz, MICROCONTROLLER, CQFP44 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| IS83D | 制造商:IDEC CORPORATION 功能描述:SENS.IND. 2W/F 24-230VAC NO |
| IS83DK | 制造商:IDEC CORPORATION 功能描述:SENS.IND. 2W/F 24-230VAC NO |
| IS83DL | 制造商:IDEC CORPORATION 功能描述:SENS.IND. 2W/F 24-230VAC NO |
| IS83K | 制造商:IDEC CORPORATION 功能描述:SENS.IND. 2W/F 24-230VAC NO |
| IS83L | 制造商:IDEC CORPORATION 功能描述:SENS.IND. 2W/F 24-230VAC NO |
發布緊急采購，3分鐘左右您將得到回復。