- 您現在的位置：買賣IC網 > PDF目錄16521 > KSZ8841-PMQL-EVAL (Micrel Inc)BOARD EVALUATION KSZ8841-PMQL PDF資料下載
參數資料
| 型號： | KSZ8841-PMQL-EVAL |
| 廠商： | Micrel Inc |
| 文件頁數： | 8/74頁 |
| 文件大?。?/td> | 0K |
| 描述： | BOARD EVALUATION KSZ8841-PMQL |
| 標準包裝： | 1 |
| 主要目的： | 接口，以太網控制器（PHY 和 MAC） |
| 嵌入式： | 否 |
| 已用 IC / 零件： | KSZ8841-PMQL |
| 主要屬性： | 1 個端口，100BASE-TX/10BASE-T |
| 次要屬性： | PCI 接口，LinkMD 線纜診斷 |
| 已供物品： | 板 |
| 產品目錄頁面： | 1114 (CN2011-ZH PDF) |
| 相關產品： | 576-2118-ND - IC MAC CTRLR 32BIT PCI 128-PQFP 576-2117-ND - IC MAC CTRLR 32BIT 128-PQFP |
| 其它名稱： | 576-1633 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁當前第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁
Micrel, Inc.
KSZ8841-PMQL
October 2007
16
M9999-100407-1.5
Physical Layer Transceiver (PHY)
100BASE-TX Transmit
The 100BASE-TX transmit function performs parallel-to-serial conversion, 4B/5B coding, scrambling, NRZ-to-NRZI
conversion, and MLT3 encoding and transmission.
The circuitry starts with a parallel-to-serial conversion, which converts the 25MHz 4-bit nibbles into a 125MHz serial bit
stream. The data and control stream is then converted into 4B/5B coding, followed by a scrambler. The serialized data
is further converted from NRZ-to-NRZI format, and then transmitted in MLT3 current output. An external 1% 3.01K
resistor for the 1:1 transformer ratio sets the output current.
The output signal has a typical rise/fall time of 4ns and complies with the ANSI TP-PMD standard regarding amplitude
balance, overshoot, and timing jitter. The wave-shaped 10BASE-T output driver is also incorporated into the 100BASE-
TX driver.
100BASE-TX Receive
The 100BASE-TX receiver function performs adaptive equalization, DC restoration, MLT3-to-NRZI conversion, data
and clock recovery, NRZI-to-NRZ conversion, de-scrambling, 4B/5B decoding, and serial-to-parallel conversion.
The receiving side starts with the equalization filter to compensate for inter-symbol interference (ISI) over the twisted
pair cable. Since the amplitude loss and phase distortion is a function of the cable length, the equalizer has to adjust its
characteristics to optimize performance. In this design, the variable equalizer makes an initial estimation based on
comparisons of incoming signal strength against some known cable characteristics, and then tunes itself for
optimization. This is an ongoing process and self-adjusts against environmental changes such as temperature
variations.
Next, the equalized signal goes through a DC restoration and data conversion block. The DC restoration circuit is used
to compensate for the effect of baseline wander and to improve the dynamic range. The differential data conversion
circuit converts the MLT3 format back to NRZI. The slicing threshold is also adaptive.
The clock recovery circuit extracts the 125MHz clock from the edges of the NRZI signal. This recovered clock is then
used to convert the NRZI signal into the NRZ format. This signal is sent through the de-scrambler followed by the 4B/5B
decoder. Finally, the NRZ serial data is converted to an MII format and provided as the input data to the MAC.
PLL Clock Synthesizer (Recovery)
The internal PLL clock synthesizer generates 125MHz, 62.5MHz, 41.66MHz, and 25MHz clocks by setting the on-chip
bus speed control register OBCR for KSZ8841-PMQL system timing. These internal clocks are generated from an
external 25MHz crystal or oscillator.
Note: Default setting is 25MHz in OBCR register, recommends the software driver to set it to 125MHz for best
performance.
Scrambler/De-scrambler (100BASE-TX Only)
The purpose of the scrambler is to spread the power spectrum of the signal to reduce electromagnetic interference
(EMI) and baseline wander.
Transmitted data is scrambled through the use of an 11-bit wide linear feedback shift register (LFSR). The scrambler
generates a 2047-bit non-repetitive sequence. Then the receiver de-scrambles the incoming data stream using the
same sequence as at the transmitter.
10BASE-T Transmit
The 10BASE-T driver is incorporated with the 100BASE-TX driver to allow for transmission using the same magnetic.
They are internally wave-shaped and pre-emphasized into outputs with typical 2.4V amplitude. The harmonic contents
are at least 27dB below the fundamental frequency when driven by an all-ones Manchester-encoded signal.
10BASE-T Receive
On the receive side, input buffers and level detecting squelch circuits are employed. A differential input receiver circuit
and a phase-locked loop (PLL) perform the decoding function.
The Manchester-encoded data stream is separated into clock signal and NRZ data. A squelch circuit rejects signals
with levels less than 400mV or with short pulse widths to prevent noise at the RXP-or-RXM input from falsely triggering
相關PDF資料 |
PDF描述 |
|---|---|
| M3CKK-1018R | IDC CABLE - MKC10K/MC10M/MPK10K |
| EBC40DCMD | CONN EDGECARD 80POS .100 WW |
| ECC22DCAT | CONN EDGECARD 44POS R/A .100 SLD |
| EBM08DRMN-S273 | CONN EDGECARD 16POS .156 WW |
| EBM08DRMD-S273 | CONN EDGECARD 16POS .156 WW |
相關代理商/技術參數 |
參數描述 |
|---|---|
| KSZ8841-PMQLI | 功能描述:以太網 IC Single Ethernet Port + 32-bit/33MHz PCI interface, Ind Temp (Lead Free) RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray |
| KSZ8842 | 制造商:MICREL 制造商全稱:Micrel Semiconductor 功能描述:2-Port Ethernet Switch with PCI Interface |
| KSZ8842-16 | 制造商:MICREL 制造商全稱:Micrel Semiconductor 功能描述:2-Port Ethernet Switch with Non-PCI Interface |
| KSZ8842-16_08 | 制造商:MICREL 制造商全稱:Micrel Semiconductor 功能描述:2-Port Ethernet Switch with Non-PCI Interface |
| KSZ8842-16_1 | 制造商:MICREL 制造商全稱:Micrel Semiconductor 功能描述:2-Port Ethernet Switch with Non-PCI Interface |
發布緊急采購，3分鐘左右您將得到回復。