參數資料
型號： KSZ8842-16MVLI
廠商： Micrel Inc
文件頁數： 102/141頁
文件大?。?/td> 0K
描述： IC ETHERNET SW 2PORT BUS 128LQFP
標準包裝： 90
控制器類型： 以太網開關控制器
接口： PCI
電源電壓： 3.1 V ~ 3.5 V
工作溫度： -40°C ~ 85°C
安裝類型： 表面貼裝
封裝/外殼： 128-LQFP
供應商設備封裝： 128-LQFP（14x14）
包裝： 托盤
產品目錄頁面： 1081 (CN2011-ZH PDF)
配用： 576-1635-ND - BOARD EVALUATION KSZ8842-16MVL
其它名稱： 576-2120
KSZ8842-16MVLI-ND
Micrel, Inc.
KSZ8842-16/32 MQL/MVL/MVLI/MBL
October 2007
63
M9999-102207-1.9
Bank 3 On-Chip Bus Control Register (0x00): OBCR
This register controls the on-chip bus speed for the KSZ8842M. It is used for power management when the external host
CPU is running at a slow frequency. The default of the on-chip bus speed is 125 MHz without EEPROM. When the
external host CPU is running at a higher clock rate, the on-chip bus should be adjusted for the best performance.
Bit
Default Value
R/W
Description
15-2
-
RO
Reserved
1-0
0x0
RW
OBSC On-Chip Bus Speed Control
00: 125MHz.
01: 62.5MHz.
10: 41.66MHz.
11: 25MHz.
Note: When external EEPROM is enabled, the bit 1 in Configparm word (0x6H) is
used to contol this speed as below:
Bit 1 = 0 , this value will be 00 for 125 MHz.
Bit 1 = 1 , this value will be 11 for 25 MHz.
(User still can write these two bits to change speed after EEPROM data loaded)
Bank 3 EEPROM Control Register (0x02): EEPCR
To support an external EEPROM, tie the EEPROM Enable (EEEN) pin to High; otherwise, tie it to Low. If an external
EEPROM is not used, the default chip Base Address (0x300), and the software programs the host MAC address. If an
EEPROM is used in the design (EEPROM Enable pin to High), the chip Base Address and host MAC address are loaded
from the EEPROM immediately after reset. The KSZ8842M allows the software to access (read and write) the EEPROM
directly; that is, the EEPROM access timing can be fully controlled by the software if the EEPROM Software Access bit is
set.
Bit
Default Value
R/W
Description
15-5
-
RO
Reserved
4
0
RW
EESA EEPROM Software Access
1: enable software to access EEPROM through bit 3 to bit 0.
0: disable software to access EEPROM.
3
-
RO
EECB EEPROM Status Bit
Data Receive from EEPROM. This bit directly reads the EEDI pin.
2-0
0x0
RW
EECB EEPROM Control Bits
Bit 2: Data Transmit to EEPROM. This bit directly controls the device’s EEDO pin.
Bit 1: Serial Clock. This bit directly controls the device’s EESK pin.
Bit 0: Chip Select for EEPROM. This bit directly controls the device’s EECS pin.
相關PDF資料
PDF描述
KSZ8842-PMBL IC ETHERNT SW 2PORT PCI 100LFBGA
KSZ8893FQL-FX IC SWITCH ETH 3PORT 128-PQFP
PIC12C509AT-04E/SN IC MCU OTP 1KX12 8SOIC
PIC16F1829T-I/SS MCU PIC 14K FLASH 1K RAM 20SSOP
V72A24C400BL3 CONVERTER MOD DC/DC 24V 400W
相關代理商/技術參數
參數描述
KSZ8842-16MVLI TR 功能描述:以太網 IC 2-Port Ethernet Switch/Repeater + Generic (8, 16-bit) bus interface(Lead Free) RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray
KSZ8842-32 制造商:MICREL 制造商全稱:Micrel Semiconductor 功能描述:2-Port Ethernet Switch with Non-PCI Interface
KSZ8842-32MQL 功能描述:以太網 IC 2-Port Ethernet Switch/Repeater + Generic (32-bit) bus interface(Lead Free) RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray
KSZ8842-32MQLA6 功能描述:IC SWITCH 10/100 32BIT 128PQFP RoHS:是 類別:集成電路 (IC) >> 接口 - 控制器 系列:- 標準包裝:4,900 系列:- 控制器類型:USB 2.0 控制器 接口:串行 電源電壓:3 V ~ 3.6 V 電流 - 電源:135mA 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:36-VFQFN 裸露焊盤 供應商設備封裝:36-QFN（6x6） 包裝:* 其它名稱:Q6396337A
KSZ8842-32MVL 功能描述:以太網 IC 2-Port Ethernet Switch/Repeater + Generic (32-bit) bus interface(Lead Free) RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*