參數資料
型號： KSZ8842-PMBL
廠商： Micrel Inc
文件頁數： 34/119頁
文件大小： 0K
描述： IC ETHERNT SW 2PORT PCI 100LFBGA
特色產品： Micrel Drives Ethernet Into the Global Automotive World
標準包裝： 260
控制器類型： 以太網開關控制器
接口： PCI
電源電壓： 3.1 V ~ 3.5 V
工作溫度： 0°C ~ 70°C
安裝類型： 表面貼裝
封裝/外殼： 100-LFBGA
供應商設備封裝： 100-LFBGA
包裝： 托盤
產品目錄頁面： 1081 (CN2011-ZH PDF)
配用： 576-1636-ND - BOARD EVALUATION KSZ8842-PMQL
其它名稱： 576-3089
Micrel, Inc.
KSZ8842-PMQL/PMBL
October 2007
21
M9999-100207-1.5
optimization. This is an ongoing process and self-adjusts against environmental changes such as temperature
variations.
Next, the equalized signal goes through a DC restoration and data conversion block. The DC restoration circuit is used
to compensate for the effect of baseline wander and to improve the dynamic range. The differential data conversion
circuit converts the MLT3 format back to NRZI. The slicing threshold is also adaptive.
The clock recovery circuit extracts the 125MHz clock from the edges of the NRZI signal. This recovered clock is then
used to convert the NRZI signal into the NRZ format. This signal is sent through the de-scrambler followed by the 4B/5B
decoder. Finally, the NRZ serial data is converted to the MII format and provided as the input data to the MAC.
PLL Clock Synthesizer (Recovery)
The internal PLL clock synthesizer generates 125MHz, 62.5MHz, 41.66MHz, and 25MHz clocks by setting the on-chip
bus speed control register OBCR for KSZ8842-PMQL/PMBL system timing. These internal clocks are generated from
an external 25MHz crystal or oscillator.
Note: Default setting is 25MHz in OBCR register, recommends the software driver to set it to 125MHz for best
performance.
Scrambler/De-scrambler (100BASE-TX Only)
The purpose of the scrambler is to spread the power spectrum of the signal to reduce electromagnetic interference
(EMI) and baseline wander. Transmitted data is scrambled through the use of an 11-bit wide linear feedback shift
register (LFSR). The scrambler generates a 2047-bit non-repetitive sequence, and the receiver then de-scrambles the
incoming data stream using the same sequence as at the transmitter.
10BASE-T Transmit
The 10BASE-T driver is incorporated with the 100BASE-TX driver to allow for transmission using the same magnetic.
They are internally wave-shaped and pre-emphasized into outputs with typical 2.3V amplitude. The harmonic contents
are at least 27dB below the fundamental frequency when driven by an all-ones Manchester-encoded signal.
10BASE-T Receive
On the receive side, input buffers and level detecting squelch circuits are employed. A differential input receiver circuit
and a phase-locked loop (PLL) perform the decoding function. The Manchester-encoded data stream is separated into
clock signal and NRZ data. A squelch circuit rejects signals with levels less than 400mV or with short pulse widths to
prevent noise at the RXP-or-RXM input from falsely triggering the decoder. When the input exceeds the squelch limit,
the PLL locks onto the incoming signal and the KSZ8842-PMQL/PMBL decodes a data frame. The receiver clock is
maintained active during idle periods in between data reception.
Power Management
The KSZ8842-PMQL/PMBL features a per port power-down mode. To save power, the user can power-down a port
that is not in use by setting bit 11 in either P1CR4 or P1MBCR register for port 1, and set bit 11 in either P2CR4 or
P2MBCR register for port 2. To bring the port back up, reset bit 11 in these registers.
In addition, there is a full switch power-down mode by PWRDN pin/ball 36. When this pin/ball is pulled-down, the entire
chip powers down. Transitioning this pin/ball from pull-down to pull-up results in a power up and chip reset.
MDI/MDI-X Auto Crossover
To eliminate the need for crossover cables between similar devices, the KSZ8842-PMQL/PMBL supports HP-Auto
MDI/MDI-X and IEEE 802.3u standard MDI/MDI-X auto crossover. HP-Auto MDI/MDI-X is the default.
The auto-sense function detects remote transmit and receive pairs and correctly assigns the transmit and receive pairs
for the KSZ8842-PMQL/PMBL device. This feature is extremely useful when end users are unaware of cable types in
addition to saving on an additional uplink configuration connection. The auto-crossover feature can be disabled through
the port control registers.
相關PDF資料
PDF描述
KSZ8893FQL-FX IC SWITCH ETH 3PORT 128-PQFP
PIC12C509AT-04E/SN IC MCU OTP 1KX12 8SOIC
PIC16F1829T-I/SS MCU PIC 14K FLASH 1K RAM 20SSOP
V72A24C400BL3 CONVERTER MOD DC/DC 24V 400W
PIC16F677-E/SS IC PIC MCU FLASH 2KX14 20SSOP
相關代理商/技術參數
參數描述
KSZ8842-PMBL AM 功能描述:以太網 IC 2-Port Ethernet Switch/Repeater + 32-bit/33MHz PCI bus interface(Lead Free) RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray
KSZ8842-PMBL AM TR 功能描述:以太網 IC 2-Port Ethernet Switch/Repeater + 32-bit/33MHz PCI bus interface(Lead Free) RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray
KSZ8842-PMBLAM 制造商:Micrel 功能描述:Ethernet Switch 2-Port 10Mbps/100Mbps
KSZ8842-PMBL-AM 功能描述:Ethernet Switch 10/100 Base-T/TX PHY PCI Interface 制造商:microchip technology 系列:- 包裝:托盤 零件狀態:要求報價 協議:以太網 功能:開關 接口:PCI 標準:10/100 Base-T/TX PHY 電壓 - 電源:3.1 V ~ 3.5 V 電流 - 電源:122mA 工作溫度:-40°C ~ 85°C 封裝/外殼:100-LFBGA 供應商器件封裝:* 標準包裝:260
KSZ8842-PMBL-EVAL 功能描述:以太網開發工具 2+1 Port 10/100 Ethernet Switch with 32b/33MHz PCI Interface (BGA Version) Eval Board RoHS:否 制造商:Micrel 產品:Evaluation Boards 類型:Ethernet Transceivers 工具用于評估:KSZ8873RLL 接口類型:RMII 工作電源電壓:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*