- 您現在的位置：買賣IC網 > PDF目錄1931 > KSZ8862-16MQL (Micrel Inc)IC SWITCH 10/100 16BIT 128-PQFP PDF資料下載
參數資料
| 型號： | KSZ8862-16MQL |
| 廠商： | Micrel Inc |
| 文件頁數： | 43/125頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC SWITCH 10/100 16BIT 128-PQFP |
| 標準包裝： | 66 |
| 系列： | KSZ8862 |
| 控制器類型： | 以太網開關控制器 |
| 接口： | PCI |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 128-BFQFP |
| 供應商設備封裝： | 128-PQFP（14x20） |
| 包裝： | 托盤 |
| 配用： | 576-1638-ND - BOARD EVALUATION KSZ8862-10FL 576-1637-ND - BOARD EVALUATION KSZ8862-100FX |
| 其它名稱： | 576-1564 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁當前第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁
Micrel, Inc.
KSZ8862-16/32MQL
April 2007
24
M9999-040407-3.0
The 100BASE-FX signal detection is summarized as below:
When FXSD1 input voltage is less than 0.2V, this is not a fiber mode or there is no fiber connection.
When FXSD1 input voltage is greater than 1.0V but less than 1.8V, this is a FX mode but no signal detected and far-end
fault generated.
When FXSD1 input voltage is greater than 2.2V, this is a FX mode with signal detected.
To ensure proper operation, a resistive voltage divider is recommended to adjust the fiber transceiver SD output voltage
swing to match the FXSD1 pin’s input voltage threshold.
100BASE-FX Far-End-Fault (FEF)
A far-end-fault (FEF) occurs when the signal detection is logically false on the receive side of the fiber transceiver. The
KSZ8862M detects a FEF when its FXSD1 input on port 1 is between 1V and 1.8V. When a FEF is detected, the
KSZ8862M signals its fiber link partner that a FEF has occurred by sending 84 1’s followed by a zero in the idle period
between frames.
By default, FEF is enabled. FEF can be disabled through register setting at P1MBCR (bit2) or P1CR4 (bit12).
100BASE-SX Operation
100BASE-SX operation is supported on port 1 only. It conforms to the TIA/EIA-785 Standard for 100BASE-SX fiber
operation. Fiber Link Negotiation Pulse (FLNP) Bursts are used to advertise link capabilities to the link partner during fiber
auto-negotiation. FLNP Bursts are equivalent to the Fast Link Pulse (FLP) Bursts used in 10BASE-T and 100BASE-TX
auto-negotiation defined by clause 28 of the IEEE802.3 Standard. Refer to respective Standard for details.
Physical Interface
For 100BASE-SX operation, port 1 interfaces with an external fiber module to drive 850nm fiber optic links up to a
maximum distance of 300m. The interface connections between the KSZ8862M and fiber module are single-ended
(common mode). 100BASE-SX signal transmission and reception are done on TXM1 (pin 49) and RXM1 (pin 46),
respectively. Refer to Micrel reference schematic for recommended interface circuit and termination.
Enabling 100BASE-SX Mode
To enable 100BASE-SX mode, tie FXSD1 (pin 44) to high (+3.3V) and 100FX/10FL (pin 41)-to-ground.
Enabling Fiber Forced Mode
In 100BASE-SX mode, the KSZ8862M supports forced mode only.
For forced mode, port 1 has auto-negotiation disabled, is forced to 100Mbps for the speed, and is set to either half or full
duplex. Optionally, flow control can be enabled to send out PAUSE frames in full duplex mode.
Forced mode and auto-negotiation disabled mode settings for 100BASE-SX fiber use the same registers (P1MBCR,
P1CR4). These registers are summarized in the Register Map section.
10BASE-FL Operation
10BASE-FL operation is supported on port 1 only. It conforms to clause 15 and 18 of the IEEE802.3 Standard for
10BASE-FL fiber operation. Fiber Link Negotiation Pulse (FLNP) Bursts are used to advertise link capabilities to the link
partner during fiber auto-negotiation. FLNP Bursts are equivalent to the Fast Link Pulse (FLP) Bursts used in 10BASE-T
and 100BASE-TX auto-negotiation defined by clause 28 of the IEEE802.3 Standard. Refer to respective Standard for
details.
Physical Interface
For 10BASE-FL operation, port 1 interfaces with an external fiber module to drive 850nm fiber optic links up to a
maximum distance of 2km. The interface connections between the KSZ8862M and fiber module are single-ended
(common mode). 10BASE-FL signal transmission and reception are done on TXM1 (pin 49) and RXM1 (pin 46),
respectively. Refer to Micrel reference schematic for recommended interface circuit and termination.
Enabling 10BASE-FL Mode
To enable 10BASE-FL mode, tie FXSD1 (pin 44) to high (+3.3V) and 100FX/10FL (pin 41)-to-ground.
Enabling Fiber Forced Mode
In 10BASE-FL mode, the KSZ8862M supports forced mode only.
For forced mode, port 1 has auto-negotiation disabled, is forced to 10Mbps for the speed, and is set to either half or full
duplex. Optionally, flow control can be enabled to send out PAUSE frames in full duplex mode.
相關PDF資料 |
PDF描述 |
|---|---|
| KSZ8862-32MQL | IC ETHERNET SW 2PORT BUS 128PQFP |
| KSZ8863MLLI | IC ETHERNET SWITCH 3PORT 48-LQFP |
| KSZ8864RMNI | IC ETHERNET SWITCH 4PORT 64QFN |
| KSZ8873FLLI | IC ETHERNET SWITCH 3PORT 64LQFP |
| KSZ8873MLLJ | IC ETHERNET SWITCH 3PORT 64LQFP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| KSZ8862-16MQL-FX | 功能描述:以太網 IC 2-Port Ethernet Switch/Repeater + Generic (16-bit) bus interface. Fiber Capabilities on Port-1(Lead Free) RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray |
| KSZ8862-32MQL | 功能描述:以太網 IC 2-Port Ethernet Switch/Repeater + Generic (32-bit) bus interface. Fiber Capabilities on Port-1(Lead Free) RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray |
| KSZ8862-32MQL-FX | 功能描述:以太網 IC 2-Port Ethernet Switch/Repeater + Generic (32-bit) bus interface. Fiber Capabilities on Port-1(Lead Free) RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray |
| KSZ8862-MQL | 制造商:MICREL 制造商全稱:Micrel Semiconductor 功能描述:2-Port Ethernet Switch with Non-PCI Interface and Fiber Support |
| KSZ8863FLL | 功能描述:以太網 IC 3-Port 10/100 Ethernet Switch with 1x FX Port and 1x TX Port (Lead Free) RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray |
發布緊急采購，3分鐘左右您將得到回復。