- 您現在的位置：買賣IC網 > PDF目錄1931 > KSZ8862-16MQL (Micrel Inc)IC SWITCH 10/100 16BIT 128-PQFP PDF資料下載
參數資料
| 型號： | KSZ8862-16MQL |
| 廠商： | Micrel Inc |
| 文件頁數： | 53/125頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC SWITCH 10/100 16BIT 128-PQFP |
| 標準包裝： | 66 |
| 系列： | KSZ8862 |
| 控制器類型： | 以太網開關控制器 |
| 接口： | PCI |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 128-BFQFP |
| 供應商設備封裝： | 128-PQFP（14x20） |
| 包裝： | 托盤 |
| 配用： | 576-1638-ND - BOARD EVALUATION KSZ8862-10FL 576-1637-ND - BOARD EVALUATION KSZ8862-100FX |
| 其它名稱： | 576-1564 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁當前第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁
Micrel, Inc.
KSZ8862-16/32MQL
April 2007
33
M9999-040407-3.0
To avoid jabber and excessive deference (as defined in the 802.3 standard), after a certain time, the KSZ8862M
discontinues the carrier sense and then raises it again quickly. This short silent time (no carrier sense) prevents other
stations from sending out packets thus keeping other stations in a carrier sense deferred state. If the port has packets to
send during a backpressure situation, then the carrier sense type backpressure is interrupted and those packets are
transmitted instead. If there are no additional packets to send, then the carrier sense type backpressure is reactivated
again until switch resources free up. If a collision occurs, then the binary exponential back-off algorithm is skipped and
carrier sense is generated immediately, thus reducing the chance of further collisions and carrier sense is maintained to
prevent packet reception.
To ensure no packet loss in 10 BASE-T or 100 BASE-TX half-duplex modes, the user must enable the following:
1.
Aggressive back off (bit 8 in SGCR1)
2.
No excessive collision drop (bit 3 in SGCR2)
Note: These bits are not set in default, since this is not the IEEE standard.
Broadcast Storm Protection
The KSZ8862M has an intelligent option to protect the switch system from receiving too many broadcast packets. As the
broadcast packets are forwarded to all ports except the source port, an excessive number of switch resources (bandwidth
and available space in transmit queues) may be utilized. The KSZ8862M has the option to include “multicast packets” for
storm control. The broadcast storm rate parameters are programmed globally, and can be enabled or disabled on a per
port basis in P1CR1 [7] and P2CR1 [7]. The rate is based on a 67ms interval for 100BT and a 670ms interval for 10BT. At
the beginning of each interval, the counter is cleared to zero and the rate limit mechanism starts to count the number of
bytes during the interval. The rate definition is described in SGCR3 [2:0] [15:8]. The default setting is 0x63 (99 decimal).
This is equal to a rate of 1%, calculated as follows:
148,800 frames/sec X 67 ms/interval X 1% = 99 frames/interval (approx.) = 0x63
Note: 148,800 frames/sec is based on 64-byte block of packets in 100BASE-T with 12 bytes of IPG and 8 bytes of
preamble between two packets.
Clock Generator
The X1 and X2 pins are connected to a 25 MHz crystal. X1 can also serve as the connector to a 3.3V, 25 MHz oscillator
(as described in the pin description).
The bus interface unit (BIU) uses BCLK (Bus Clock) for synchronous accesses. The maximum host port frequency is 50
MHz for VLBus-like and burst mode (32-bit interface only).
Bus Interface Unit (BIU)
The host interface of the BIU is designed to communicate with embedded processors. The host interface of the
KSZ8862M is a generic bus interface. Some glue logic may be required when the interface talks to various buses and
processors.
In terms of transfer type, the BIU can support two transfers: asynchronous transfer and synchronous transfer. To support
these transfers (asynchronous and synchronous), the BIU provides three groups of signals:
1.
Synchronous signals
2.
Asynchronous signals
3.
Common signals used for both synchronous and asynchronous transfers.
Since both synchronous and asynchronous signals are independent of each other, synchronous burst transfer and
asynchronous transfer can be mixed or interleaved but cannot be overlapped (due to the sharing of the common signals).
In terms of physical data bus size, the KSZ8862M supports 8, 16, and 32 bit host/industrial standard data bus sizes.
Given a physical data bus size, the KSZ8862M supports 8, 16, or 32-bit data transfers depending upon the size of the
physical data bus. For example, for a 32-bit system/host data bus, it allows 8, 16, and 32-bit data transfers (KSZ8862-
32MQL); for a 16-bit system/host data bus, it allows 8 and 16-bit data transfers (KSZ8862-16MQL); and for 8-bit
system/host data bus, it only allows 8-bit data transfers (KSZ8862-16MQL).
Note that KSZ8862M does not support internal data byte-swap but it does support internal data word-swap. This means
that the system/host data bus HD [7:0] has to connect to both D [7:0] and D [15:8] for 8-bit data bus interfaces. However,
the system/host data bus HD [15:8] and HD [7:0] just connects to D [15:8] and D [7:0], respectively, for 16-bit data bus
interface; there is no need to connect HD [31:24] and HD [23:16] to D [31:24] and D [23:16].
相關PDF資料 |
PDF描述 |
|---|---|
| KSZ8862-32MQL | IC ETHERNET SW 2PORT BUS 128PQFP |
| KSZ8863MLLI | IC ETHERNET SWITCH 3PORT 48-LQFP |
| KSZ8864RMNI | IC ETHERNET SWITCH 4PORT 64QFN |
| KSZ8873FLLI | IC ETHERNET SWITCH 3PORT 64LQFP |
| KSZ8873MLLJ | IC ETHERNET SWITCH 3PORT 64LQFP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| KSZ8862-16MQL-FX | 功能描述:以太網 IC 2-Port Ethernet Switch/Repeater + Generic (16-bit) bus interface. Fiber Capabilities on Port-1(Lead Free) RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray |
| KSZ8862-32MQL | 功能描述:以太網 IC 2-Port Ethernet Switch/Repeater + Generic (32-bit) bus interface. Fiber Capabilities on Port-1(Lead Free) RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray |
| KSZ8862-32MQL-FX | 功能描述:以太網 IC 2-Port Ethernet Switch/Repeater + Generic (32-bit) bus interface. Fiber Capabilities on Port-1(Lead Free) RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray |
| KSZ8862-MQL | 制造商:MICREL 制造商全稱:Micrel Semiconductor 功能描述:2-Port Ethernet Switch with Non-PCI Interface and Fiber Support |
| KSZ8863FLL | 功能描述:以太網 IC 3-Port 10/100 Ethernet Switch with 1x FX Port and 1x TX Port (Lead Free) RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray |
發布緊急采購，3分鐘左右您將得到回復。