- 您現在的位置：買賣IC網 > PDF目錄4594 > KSZ8995M (Micrel Inc)IC SWITCH 10/100 5PORT 128PQFP PDF資料下載
參數資料
| 型號： | KSZ8995M |
| 廠商： | Micrel Inc |
| 文件頁數： | 16/73頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC SWITCH 10/100 5PORT 128PQFP |
| 標準包裝： | 66 |
| 系列： | * |
| 類型： | * |
| 應用： | * |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 128-BFQFP |
| 供應商設備封裝： | 128-PQFP（14x20） |
| 包裝： | 托盤 |
| 產品目錄頁面： | 1081 (CN2011-ZH PDF) |
| 配用： | 576-1607-ND - BOARD EVAL EXPERIMENT KSZ8995MA |
| 其它名稱： | 576-1038 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁當前第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁
December 2003
23
M9999-120403
KS8995M
Micrel
detect, and FXSDx ‘L’ is below the 1.25V reference to indicate no signal. When FXSDx is below 0.6V then 100BaseFX mode
is disabled. Since there is no auto-negotiation for 100BaseFX mode, ports 4 and 5 must be forced to either full or half-duplex.
Note that strap in options exist to set duplex mode for port 4, but not for port 5.
100BaseFX Far End Fault
Far end fault occurs when the signal detection is logically false from the receive fiber module. When this occurs, the
transmission side signals the other end of the link by sending 84 1s followed by a zero in the idle period between frames. The
far end fault may be disabled through register settings.
10BaseT Transmit
The output 10BaseT driver is incorporated into the 100BaseT driver to allow transmission with the same magnetics. They are
internally wave-shaped and pre-emphasized into outputs with a typical 2.3V amplitude. The harmonic contents are at least
27dB below the fundamental when driven by an all-ones Manchester-encoded signal.
10BaseT Receive
On the receive side, input buffer and level detecting squelch circuits are employed. A differential input receiver circuit and a
PLL perform the decoding function. The Manchester-encoded data stream is separated into clock signal and NRZ data. A
squelch circuit rejects signals with levels less than 400mV or with short pulse widths in order to prevent noises at the RXP or
RXM input from falsely triggering the decoder. When the input exceeds the squelch limit, the PLL locks onto the incoming signal
and the KS8995M decodes a data frame. The receiver clock is maintained active during idle periods in between data reception.
Power Management
The KS8995M features a per port power down mode. To save power the user can power down ports that are not in use by setting
port control registers or MII control registers. In addition, it also supports full chip power down mode. When activated, the entire
chip will be shut down.
MDI/MDI-X Auto Crossover
The KS8995M supports MDI/MDI-X auto crossover. This facilitates the use of either a straight connection CAT-5 cable or a
crossover CAT-5 cable. The auto-sense function will detect remote transmit and receive pairs, and correctly assign the transmit
and receive pairs from the Micrel device. This can be highly useful when end users are unaware of cable types and can also
save on an additional uplink configuration connection. The auto crossover feature may be disabled through the port control
registers.
Auto-Negotiation
The KS8995M conforms to the auto-negotiation protocol as described by the 802.3 committee. Auto-negotiation allows UTP
(Unshielded Twisted Pair) link partners to select the best common mode of operation. In auto-negotiation the link partners
advertise capabilities across the link to each other. If auto-negotiation is not supported or the link partner to the KS8995M is
forced to bypass auto-negotiation, then the mode is set by observing the signal at the receiver. This is known as parallel mode
because while the transmitter is sending auto-negotiation advertisements, the receiver is listening for advertisements or a fixed
signal protocol.
The flow for the link set up is depicted in Figure 4.
Start Auto Negotiation
Force Link Setting
Listen for 10BaseT
Link Pulses
Listen for 100BaseTX
Idles
Attempt
Auto-Negotiation
Link Mode Set
Bypass
Auto-Negotiation
and Set Link Mode
Link Mode Set ?
Parallel
Operation
Join Flow
No
Yes
No
Figure 4. Auto-Negotiation
相關PDF資料 |
PDF描述 |
|---|---|
| RSM40DTAT | CONN EDGECARD 80POS R/A .156 SLD |
| LFEC6E-3QN208C | IC FPGA 6.1KLUTS 147I/O 208-PQFP |
| LFEC6E-3Q208C | IC FPGA 6.1KLUTS 147I/O 208-PQFP |
| RMM40DTAT | CONN EDGECARD 80POS R/A .156 SLD |
| LFXP3E-5Q208C | IC FPGA 3.1KLUTS 136I/O 208-PQFP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| KSZ8995MA | 功能描述:以太網 IC 5 Port 10/100 Switch with PHY and Frame Buffers (Lead Free) RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray |
| KSZ8995MA4 | 功能描述:IC SWITCH 5-PORT 10/100 128PQFP RoHS:是 類別:集成電路 (IC) >> 專用 IC 系列:* 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- 類型:調幀器 應用:數據傳輸 安裝類型:表面貼裝 封裝/外殼:400-BBGA 供應商設備封裝:400-PBGA（27x27） 包裝:散裝 |
| KSZ8995MAB3 | 功能描述:IC SWITCH 5-PORT 10/100 128PQFP RoHS:是 類別:集成電路 (IC) >> 專用 IC 系列:* 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- 類型:調幀器 應用:數據傳輸 安裝類型:表面貼裝 封裝/外殼:400-BBGA 供應商設備封裝:400-PBGA（27x27） 包裝:散裝 |
| KSZ8995MA-EVAL | 功能描述:以太網開發工具 KSZ8995MA Evaluation Board RoHS:否 制造商:Micrel 產品:Evaluation Boards 類型:Ethernet Transceivers 工具用于評估:KSZ8873RLL 接口類型:RMII 工作電源電壓: |
| KSZ8995MAI | 功能描述:以太網 IC 5 Port 10/100 Switch with PHY and Frame Buffers (Lead Free) RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray |
發布緊急采購，3分鐘左右您將得到回復。