參數資料
型號: M29F105B
廠商: 意法半導體
英文描述: 1Mbit (64Kb x16, Block Erase) Single Supply Flash Memory(1Mb閃速存儲器)
中文描述: 為1Mbit(64Kb的x16插槽,塊擦除)單電源閃存存儲器(1MB閃速存儲器)
文件頁數: 14/28頁
文件大?。?/td> 200K
代理商: M29F105B
Symbol
Alt
Parameter
M29F105B
Unit
-55
-70
-90
V
CC
= 5V
±
5%
V
CC
= 5V
±
10%
High Speed
Interface
Standard
Interface
Min
Max
Min
Max
Min
Max
t
AVAV
t
WC
Address Validto Next Address Valid
55
70
90
ns
t
ELWL
t
CS
Chip Enable Low to Write Enable Low
0
0
0
ns
t
WLWH
t
WP
Write Enable Low to Write Enable High
30
35
45
ns
t
DVWH
t
DS
Input Valid to Write Enable High
25
30
45
ns
t
WHDX
t
DH
Write Enable High to Input Transition
0
0
0
ns
t
WHEH
t
CH
Write Enable High to Chip Enable High
0
0
0
ns
t
WHWL
t
WPH
Write Enable High to Write Enable Low
20
20
20
ns
t
AVWL
t
AS
Address Valid to Write Enable Low
0
0
0
ns
t
WLAX
t
AH
Write Enable Low to Address Transition
35
45
45
ns
t
GHWL
Output Enable High to Write Enable
Low
0
0
0
ns
t
VCHEL
t
VCS
V
CC
High to Chip Enable Low
50
50
50
μ
s
t
WHGL
t
OEH
Write Enable High to Output Enable
Low
0
0
0
ns
Table15. WriteAC Characteristics,Write Enable Controlled
(T
A
= 0 to 70
°
C or –40 to85
°
C)
Erase Suspend (ES) Instruction.
The Block
Eraseoperationmaybe suspendedbythisinstruc-
tion which consists of writing the command B0h
withoutany specificaddress.No Codedcyclesare
required. It permits reading of data from another
block and programming in another block while an
erase operation is in progress. Erase suspend is
accepted only during the Block Erase instruction
execution. Writing this command during Erase
timeout will, in addition to suspending the erase,
terminate the timeout. The Toggle bit DQ6 stops
togglingwhentheP/E.C.is suspended.The Toggle
bitswillstoptogglingbetween0.1
μ
s and15
μ
s after
the Erase Suspend(ES) command has been writ-
ten. The device will then automatically be set to
Read Memory Array mode. When erase is sus-
pended, a Read from blocks being erased will
output DQ2 toggling and DQ6 at ’1’. A Read from
a blocknotbeingerasedreturnsvaliddata. During
suspension the memory will respond only to the
Erase Resume ER and the Program PG instruc-
tions. AProgram operation can be initiatedduring
erase suspend in one of the blocks not being
erased. Itwill resultin bothDQ2 andDQ6toggling
whenthedataisbeingprogrammed.ARead/Reset
command will definitively abort erasure and result
in invaliddata in the blocksbeing erased.
EraseResume(ER)Instruction.
Ifan EraseSus-
pend instruction was previously executed, the
erase operation may be resumed by giving the
command 30h, at any address, and without any
Codedcycles.
14/28
M29F105B
相關PDF資料
PDF描述
M29F200B 2Mbit (256Kb x8 or 128Kb x16, Boot Block) Single Supply Flash Memory(2M位閃速存儲器)
M29F400BT90N1E 4 Mbit (512Kb x8 or 256Kb x16, Boot Block) single supply Flash memory
M29F400BT90N1F 4 Mbit (512Kb x8 or 256Kb x16, Boot Block) single supply Flash memory
M29F400BT90N3E 4 Mbit (512Kb x8 or 256Kb x16, Boot Block) single supply Flash memory
M29F400BT90N3F 4 Mbit (512Kb x8 or 256Kb x16, Boot Block) single supply Flash memory
相關代理商/技術參數
參數描述
M29F160BT70N1 功能描述:閃存 2Mx8 or 1Mx16 70ns RoHS:否 制造商:ON Semiconductor 數據總線寬度:1 bit 存儲類型:Flash 存儲容量:2 MB 結構:256 K x 8 定時類型: 接口類型:SPI 訪問時間: 電源電壓-最大:3.6 V 電源電壓-最小:2.3 V 最大工作電流:15 mA 工作溫度:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel
M29F160FB55N3E2 制造商:Micron Technology Inc 功能描述:AUTOMOTIVE 5V - Trays 制造商:Micron Technology Inc 功能描述:IC FLASH 16MBIT 55NS 48TSOP
M29F160FB55N3F2 制造商:Micron Technology Inc 功能描述:AUTOMOTIVE 5V - Tape and Reel
M29F160FB55N3F2 TR 制造商:Micron Technology Inc 功能描述:IC FLASH 16MBIT 55NS 48TSOP
M29F160FB5AN6E2 制造商:Micron Technology Inc 功能描述:AUTOMOTIVE 5V - Trays 制造商:Micron Technology Inc 功能描述:NOR Flash Parallel 5V 16Mbit 2M/1M x 8bit/16bit 55ns 48-Pin TSOP Tray 制造商:Micron Technology Inc 功能描述:IC FLASH 16MBIT 55NS 48TSOP