- 您現(xiàn)在的位置：買賣IC網 > PDF目錄69021 > MB91110PMT2 (FUJITSU LTD) 32-BIT, 50 MHz, RISC MICROCONTROLLER, PQFP144 PDF資料下載
參數資料
| 型號： | MB91110PMT2 |
| 廠商： | FUJITSU LTD |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 32-BIT, 50 MHz, RISC MICROCONTROLLER, PQFP144 |
| 封裝： | PLASTIC, LQFP-144 |
| 文件頁數： | 6/94頁 |
| 文件大?。?/td> | 1099K |
| 代理商： | MB91110PMT2 |
第1頁第2頁第3頁第4頁第5頁當前第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁
MB91110 Series
14
s
s HANDLING DEVICES
Preventing Latch-up
The “Latch-up” phenomenon may be generated if a voltage in excess of VCC or lower than VSS is applied to the
input/output pins, or if the voltage exceeds the rating between VCC and VSS. If latch-up is generated, the electrical
current increases significantly and may destroy certain components due to the excessive heat, so great care
must be taken to ensure that the maximum rating is not exceeded during use.
Handling Unused Input Pins
Input pins that are not used should be pulled up or down as they may cause erroneous operations if they are
left open.
External Reset Input
“L” level should be input to the RST pin, which is required for at least five machine cycles to ensure the internal
status is reset.
Using External Clocks
If external clock is used, X0 pin should be provided, and X1 pin should be provided with reverse phase to X0
pin input. If the STOP mode (oscillation stop mode) is used simultaneously, the X1 pin is stopped with the “H”
output. So, when STOP mode is specified, approximately 1 k
of resistance should be added externally. An
example of the external clock usage methods is shown in the following circuit.
Note : Resistance must be added to the X1 pin if the STOP mode (oscillation stop mode) is used.
Power Supply Pins
In products with multiple Vcc or Vss pins, the pins of the same potential are internally connected in the device
to avoid abnormal operations including latch-up. However you must connect the pins to an external power and
a ground line to lower the electro-magnetic emission level to prevent abnormal operation of strobe signals caused
by the rise in the ground level, and to conform to the total current rating.
Make sure to connect Vcc and Vss pins via the lowest impedance to power lines.
It is recommended to provide a bypass capacitor of around 0.1 F between Vcc and Vss pins near the device.
Crystal Oscillator Circuits
Noise around the X0 or X1 pins may cause erroneous operation. Make sure to provide bypass capacitors via
shortest distances from X0, X1 pins, crystal oscillator (or ceramic resonator) and ground lines, and make sure
that lines of oscillation circuits not cross the lines of other circuit.
A printed circuit board artwork surrounding the X0 and X1 pins with ground area for stabilizing the operation is
highly recommended .
X0
X1
MB91110
Example of External Clock Usage (normal case)
相關PDF資料 |
PDF描述 |
|---|---|
| MB91110PMT2 | 32-BIT, 50 MHz, RISC MICROCONTROLLER, PQFP144 |
| MB91121PFV | 32-BIT, 50 MHz, RISC MICROCONTROLLER, PQFP120 |
| MB91154PFV-G-XXX | 32-BIT, MROM, 33 MHz, RISC MICROCONTROLLER, PQFP144 |
| MB91F155APFV-G | 32-BIT, FLASH, 33 MHz, RISC MICROCONTROLLER, PQFP144 |
| MB91233LLGA-G-xxx-BNDE1 | 32-BIT, FLASH, 33.6 MHz, RISC MICROCONTROLLER, PQFP120 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MB911110PMT2 | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:32-Bit RISC Microcontroller |
| MB91121 | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:32-bit RISC Microcontroller |
| MB91121PFV | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:32-bit RISC Microcontroller CMOS |
| MB91133 | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:32-Bit RISC Microcontroller |
| MB91133PBT | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:32-Bit RISC Microcontroller |
發(fā)布緊急采購，3分鐘左右您將得到回復。