- 您現在的位置：買賣IC網 > PDF目錄3944 > MC8610PX1333JB (Freescale Semiconductor)MPU E600 CORE 1333MHZ 783-PBGA PDF資料下載
參數資料
| 型號： | MC8610PX1333JB |
| 廠商： | Freescale Semiconductor |
| 文件頁數： | 75/96頁 |
| 文件大?。?/td> | 0K |
| 描述： | MPU E600 CORE 1333MHZ 783-PBGA |
| 標準包裝： | 36 |
| 系列： | MPC86xx |
| 處理器類型： | 32-位 MPC86xx PowerPC |
| 速度： | 1.333GHz |
| 電壓： | 1.025V |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 783-BBGA，F(xiàn)CBGA |
| 供應商設備封裝： | 783-FCPBGA（29x29） |
| 包裝： | 托盤 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁當前第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁
Hardware Design Considerations
MPC8610 Integrated Host Processor Hardware Specifications, Rev. 2
Freescale Semiconductor
77
Note the following:
SDnAVDD should be a filtered version of SVDD.
Signals on the SerDes interface are fed from the SVDD power plane.
3.3
Decoupling Recommendations
Due to large address and data buses, and high operating frequencies, the device can generate transient power surges and high
frequency noise in its power supply, especially while driving large capacitive loads. This noise must be prevented from reaching
other components in the MPC8610 system, and the device itself requires a clean, tightly regulated source of power. Therefore,
it is recommended that the system designer place at least one decoupling capacitor at each VDD, BVDD, OVDD, GVDD,
VDD_Core, and VDD_PLAT pin of the device. These decoupling capacitors should receive their power from separate VDD,
BVDD, OVDD, GVDD, VDD_Core, VDD_PLAT, and GND power planes in the PCB, utilizing short traces to minimize
inductance. Capacitors may be placed directly under the device using a standard escape pattern. Others may surround the part.
These capacitors should have a value of 0.01 or 0.1 F. Only ceramic SMT (surface mount technology) capacitors should be
used to minimize lead inductance, preferably 0402 or 0603 sizes.
In addition, it is recommended that there be several bulk storage capacitors distributed around the PCB, feeding the VDD, BVDD,
OVDD, GVDD, VDD_Core, and VDD_PLAT planes, to enable quick recharging of the smaller chip capacitors. These bulk
capacitors should have a low ESR (equivalent series resistance) rating to ensure the quick response time necessary. They should
also be connected to the power and ground planes through two vias to minimize inductance. Suggested bulk
capacitors—100–330 F (AVX TPS tantalum or Sanyo OSCON).
3.4
SerDes Block Power Supply Decoupling Recommendations
The SerDes block requires a clean, tightly regulated source of power (SnVDD and XnVDD) to ensure low jitter on transmit and
reliable recovery of data in the receiver. An appropriate decoupling scheme is outlined below.
Only surface mount technology (SMT) capacitors should be used to minimize inductance. Connections from all capacitors to
power and ground should be done with multiple vias to further reduce inductance.
First, the board should have at least 10 x 10-nF SMT ceramic chip capacitors as close as possible to the supply balls
of the device. Where the board has blind vias, these capacitors should be placed directly below the chip supply and
ground connections. Where the board does not have blind vias, these capacitors should be placed in a ring around the
device as close to the supply and ground connections as possible.
Second, there should be a 1-F ceramic chip capacitor on each side of the device. This should be done for all SerDes
supplies.
Third, between the device and any SerDes voltage regulator there should be a 10-F, low equivalent series resistance
(ESR) SMT tantalum chip capacitor and a 100-F, low ESR SMT tantalum chip capacitor. This should be done for all
SerDes supplies.
3.5
Connection Recommendations
To ensure reliable operation, it is highly recommended to connect unused inputs to an appropriate signal level. All unused active
low inputs should be tied to VDD, BVDD, OVDD, GVDD, VDD_Core, VDD_PLAT, XnVDD, and SnVDD as required. All unused
active high inputs should be connected to GND. All NC (no-connect) signals must remain unconnected. Power and ground
connections must be made to all external VDD, BVDD, OVDD, GVDD, VDD_Core, VDD_PLAT, XnVDD, SnVDD, and GND pins
of the device.
Special cases:
Local Bus—If parity is not used, tie LDP[0:3] to ground via a 4.7-k
Ω resistor, tie LPBSE to OV
DD via a 4.7-kΩ resistor
(pull-up resistor). For systems which boot from local bus (GPCM)-controlled Flash, a pull up on LGPL4 is required.
相關PDF資料 |
PDF描述 |
|---|---|
| 345-012-523-802 | CARDEDGE 12POS DUAL .100 GREEN |
| 345-012-523-801 | CARDEDGE 12POS DUAL .100 GREEN |
| MC8610PX1066JB | MPU E600 CORE 1066MHZ 783-PBGA |
| 345-012-523-204 | CARDEDGE 12POS DUAL .100 GREEN |
| 345-012-523-202 | CARDEDGE 12POS DUAL .100 GREEN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MC8610PX1333JZ | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:MPC8610 Integrated Host Processor Hardware Specifications |
| MC8610PX800G | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Integrated Host Processor Hardware Specifications |
| MC8610PX800GB | 功能描述:微處理器 - MPU REV 1.1 8610 1.0V 105C RoHS:否 制造商:Atmel 處理器系列:SAMA5D31 核心:ARM Cortex A5 數據總線寬度:32 bit 最大時鐘頻率:536 MHz 程序存儲器大小:32 KB 數據 RAM 大小:128 KB 接口類型:CAN, Ethernet, LIN, SPI,TWI, UART, USB 工作電源電壓:1.8 V to 3.3 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:FBGA-324 |
| MC8610PX800GZ | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:MPC8610 Integrated Host Processor Hardware Specifications |
| MC8610PX800J | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Integrated Host Processor Hardware Specifications |
發布緊急采購，3分鐘左右您將得到回復。