參數資料
型號： MC8610PX1333JB
廠商： Freescale Semiconductor
文件頁數： 79/96頁
文件大?。?/td> 0K
描述： MPU E600 CORE 1333MHZ 783-PBGA
標準包裝： 36
系列： MPC86xx
處理器類型： 32-位 MPC86xx PowerPC
速度： 1.333GHz
電壓： 1.025V
安裝類型： 表面貼裝
封裝/外殼： 783-BBGA，F(xiàn)CBGA
供應商設備封裝： 783-FCPBGA（29x29）
包裝： 托盤
MPC8610 Integrated Host Processor Hardware Specifications, Rev. 2
Hardware Design Considerations
Freescale Semiconductor
80
3.9
JTAG Configuration Signals
Correct operation of the JTAG interface requires configuration of a group of system control pins as demonstrated in Figure 53.
Care must be taken to ensure that these pins are maintained at a valid deasserted state under normal operating conditions as most
have asynchronous behavior and spurious assertion will give unpredictable results.
Boundary-scan testing is enabled through the JTAG interface signals. The TRST signal is optional in the IEEE 1149.1
specification, but is provided on all processors that implement the Power Architecture technology. The device requires TRST
to be asserted during reset conditions to ensure the JTAG boundary logic does not interfere with normal chip operation. While
it is possible to force the TAP controller to the reset state using only the TCK and TMS signals, more reliable power-on reset
performance will be obtained if the TRST signal is asserted during power-on reset. Because the JTAG interface is also used for
accessing the common on-chip processor (COP) function, simply tying TRST to HRESET is not practical.
The COP function of these processors allows a remote computer system (typically a PC with dedicated hardware and debugging
software) to access and control the internal operations of the processor. The COP port connects primarily through the JTAG
interface of the processor, with some additional status monitoring signals. The COP port requires the ability to independently
assert HRESET or TRST in order to fully control the processor. If the target system has independent reset sources, such as
voltage monitors, watchdog timers, power supply failures, or push-button switches, then the COP reset signals must be merged
into these signals with logic.
The arrangement shown in Figure 52 allows the COP port to independently assert HRESET or TRST, while ensuring that the
target can drive HRESET as well.
The COP interface has a standard header, shown in Figure 52, for connection to the target system, and is based on the 0.025"
square-post, 0.100" centered header assembly (often called a Berg header). The connector typically has pin 14 removed as a
connector key.
The COP header adds many benefits such as breakpoints, watchpoints, register and memory examination/modification, and
other standard debugger features. An inexpensive option can be to leave the COP header unpopulated until needed.
There is no standardized way to number the COP header shown in Figure 53; consequently, many different pin numbers have
been observed from emulator vendors. Some are numbered top-to-bottom then left-to-right, while others use left-to-right then
top-to-bottom, while still others number the pins counter clockwise from pin 1 (as with an IC). Regardless of the numbering,
the signal placement recommended in Figure 53 is common to all known emulators.
3.9.1
Termination of Unused Signals
If the JTAG interface and COP header will not be used, Freescale recommends the following connections:
TRST should be tied to HRESET through a 0-k
Ω isolation resistor so that it is asserted when the system reset signal
(HRESET) is asserted, ensuring that the JTAG scan chain is initialized during the power-on reset flow. Freescale
recommends that the COP header be designed into the system as shown in Figure 53. If this is not possible, the
isolation resistor will allow future access to TRST in case a JTAG interface may need to be wired onto the system in
future debug situations.
Tie TCK to OVDD through a 10-kΩ resistor. This will prevent TCK from changing state and reading incorrect data
into the device.
No connection is required for TDI, TMS, or TDO.
相關PDF資料
PDF描述
345-012-523-802 CARDEDGE 12POS DUAL .100 GREEN
345-012-523-801 CARDEDGE 12POS DUAL .100 GREEN
MC8610PX1066JB MPU E600 CORE 1066MHZ 783-PBGA
345-012-523-204 CARDEDGE 12POS DUAL .100 GREEN
345-012-523-202 CARDEDGE 12POS DUAL .100 GREEN
相關代理商/技術參數
參數描述
MC8610PX1333JZ 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:MPC8610 Integrated Host Processor Hardware Specifications
MC8610PX800G 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Integrated Host Processor Hardware Specifications
MC8610PX800GB 功能描述:微處理器 - MPU REV 1.1 8610 1.0V 105C RoHS:否 制造商:Atmel 處理器系列:SAMA5D31 核心:ARM Cortex A5 數據總線寬度:32 bit 最大時鐘頻率:536 MHz 程序存儲器大小:32 KB 數據 RAM 大小:128 KB 接口類型:CAN, Ethernet, LIN, SPI,TWI, UART, USB 工作電源電壓:1.8 V to 3.3 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:FBGA-324
MC8610PX800GZ 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:MPC8610 Integrated Host Processor Hardware Specifications
MC8610PX800J 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Integrated Host Processor Hardware Specifications
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*