參數資料
型號: MCZ33742EG
廠商: Freescale Semiconductor
文件頁數: 54/71頁
文件大?。?/td> 0K
描述: IC SYSTEM BASIS CHIP CAN 28-SOIC
標準包裝: 26
應用: 自動
電流 - 電源: 42mA
電源電壓: 5.5 V ~ 18 V
工作溫度: -40°C ~ 125°C
安裝類型: 表面貼裝
封裝/外殼: 28-SOIC(0.295",7.50mm 寬)
供應商設備封裝: 28-SOIC W
包裝: 管件
產品目錄頁面: 808 (CN2011-ZH PDF)
Analog Integrated Circuit Device Data
58
Freescale Semiconductor
33742
TYPICAL APPLICATIONS
C3:
47 F, ESR < 10
V2 REGULATOR: OPERATING WITH EXTERNAL BALLAST TRANSISTOR
The V2 regulator is a tracking regulator of the VDD output. Its accuracy relative to VDD is ±1.0%. It requires external
decoupling and stabilizing capacitors.
The recommended value are as follows:
22
F, ESR < 5.0
47
F, ESR < 10
The V2 pin has two functions: it is a sense input for the V2 regulator and is a 5.0 V power supply input to the CAN interface.
With respect to ballast transistor selection, either PNP or PMOS transistors may be used. A resistor between base and emitter
(or source and drain) is necessary to ensure proper operation and optimized performances. Recommended bipolar transistor is
MJD32C.
V2 REGULATOR: OPERATION WITHOUT BALLAST TRANSISTOR
The external ballast transistor is optional. If the application does not requires more than the maximum output current capability
of the VDD regulator, then the ballast transistor can be omitted. The thermal aspects must be analyzed as well.
The electrical connection is illustrated in Figure 32.
Figure 32. V2 Regulator Electrical Connection
FAILURE ON VDD, WDOG, RESET, AND INT PINS
The paragraphs below describe the behavior of the device and of the INT, RST, and WDOG pins at power-up and under failure
of the VDD regulator.
POWER-UP AND SBC ENTERING NORMAL OPERATION
After power-up the 33742 enters Normal Request mode (CAN interface is in TXRX mode): VDD is on and V2 is off.
After 350 ms if no watchdog is written (no TIM1 register write), a reset occurs and the 33742 returns to Normal Request mode.
During this sequence WDOG is active (low level).
Once watchdog is written, the 33742 goes to Normal mode: VDD is still on and V2 turns on, WDOG is no longer active, and
the RST pin is HIGH. If watchdog is not refreshed, the 33742 generates a reset and returns to Normal Request mode. Figure 33,
illustrates the operation.
VDD
VSUP
V2CTRL
RST
C3
C4
C1
C2
VDD
RESET
33742
V2
No Connect
Components List
C1: 22
F
C2: 100 nF
C3: >10
F
C4: 100 nF
MCU
VPWR
相關PDF資料
PDF描述
H2MXH-1618M DIP CABLE - HDM16H/AE16M/X
PCK0G331MCO1GS CAP ALUM 330UF 4V 20% SMD
SDR0805-681KL INDUCTOR POWER 680UH 10% SMD
AD587JR-REEL IC VREF SERIES PREC 10V 8-SOIC
B82422A3151K100 INDUCTOR .15UH 390MA 1210 10%
相關代理商/技術參數
參數描述
MCZ33742EGR2 功能描述:網絡控制器與處理器 IC SBC-E-HS-CAN RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流(最大值):595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
MCZ33742SEG 功能描述:網絡控制器與處理器 IC SBC-E-HS-CAN RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流(最大值):595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
MCZ33742SEGR2 功能描述:網絡控制器與處理器 IC SBC-E-HS-CAN RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流(最大值):595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
MCZ33780EG 功能描述:多路器開關 IC DBUS MASTER RoHS:否 制造商:Texas Instruments 通道數量:1 開關數量:4 開啟電阻(最大值):7 Ohms 開啟時間(最大值): 關閉時間(最大值): 傳播延遲時間:0.25 ns 工作電源電壓:2.3 V to 3.6 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UQFN-16
MCZ33780EG 制造商:Freescale Semiconductor 功能描述:DUAL DBUS MASTER INTERFACE 16SOIC