參數資料
型號： MJ80C32U-25:D
廠商： ATMEL CORP
元件分類： 微控制器/微處理器
英文描述： MICROCONTROLLER
文件頁數： 51/109頁
文件大?。?/td> 10824K
31
AT32UC3A
status register. Upon entry into Debug mode, hardware sets the SR[D] bit and jumps to the
Debug Exception handler. By default, debug mode executes in the exception context, but with
dedicated Return Address Register and Return Status Register. These dedicated registers
remove the need for storing this data to the system stack, thereby improving debuggability. The
mode bits in the status register can freely be manipulated in Debug mode, to observe registers
in all contexts, while retaining full privileges.
Debug mode is exited by executing the retd instruction. This returns to the previous context.
9.4.5
Entry points for events
Several different event handler entry points exists. In AVR32 UC, the reset address is
0x8000_0000. This places the reset address in the boot flash memory area.
TLB miss exceptions and scall have a dedicated space relative to EVBA where their event han-
dler can be placed. This speeds up execution by removing the need for a jump instruction placed
at the program address jumped to by the event hardware. All other exceptions have a dedicated
event routine entry point located relative to EVBA. The handler routine address identifies the
exception source directly.
AVR32UC uses the ITLB and DTLB protection exceptions to signal a MPU protection violation.
ITLB and DTLB miss exceptions are used to signal that an access address did not map to any of
the entries in the MPU. TLB multiple hit exception indicates that an access address did map to
multiple TLB entries, signalling an error.
All external interrupt requests have entry points located at an offset relative to EVBA. This
autovector offset is specified by an external Interrupt Controller. The programmer must make
sure that none of the autovector offsets interfere with the placement of other code. The autovec-
tor offset has 14 address bits, giving an offset of maximum 16384 bytes.
Special considerations should be made when loading EVBA with a pointer. Due to security con-
siderations, the event handlers should be located in non-writeable flash memory, or optionally in
a privileged memory protection region if an MPU is present.
If several events occur on the same instruction, they are handled in a prioritized way. The priority
ordering is presented in Table 9-4. If events occur on several instructions at different locations in
the pipeline, the events on the oldest instruction are always handled before any events on any
younger instruction, even if the younger instruction has events of higher priority than the oldest
instruction. An instruction B is younger than an instruction A if it was sent down the pipeline later
than A.
The addresses and priority of simultaneous events are shown in Table 9-4. Some of the excep-
tions are unused in AVR32 UC since it has no MMU, coprocessor interface or floating-point unit.
32058K
AVR32-01/12
相關PDF資料
PDF描述
MQ80C32E-36:RD 8-BIT, 36 MHz, MICROCONTROLLER, CQFP44
S80C32-40:R 8-BIT, 40 MHz, MICROCONTROLLER, PQCC44
S80C52EXXX-30:D 8-BIT, MROM, 30 MHz, MICROCONTROLLER, PQCC44
SC80C52XXX-36/883 8-BIT, MROM, 36 MHz, MICROCONTROLLER, CDIP40
S83C154TXXX-25 8-BIT, MROM, 25 MHz, MICROCONTROLLER, PQCC44
相關代理商/技術參數
參數描述
MJ8100 制造商:ASI 功能描述:8100 N11E4C
MJ8100R 制造商:SEME-LAB 制造商全稱:Seme LAB 功能描述:Bipolar PNP Device in a Hermetically sealed TO39
MJ-82-1 制造商:SPC Multicomp 功能描述:SOCKET PCB DC POWER 制造商:SPC Multicomp 功能描述:SOCKET, PCB, DC POWER 制造商:SPC Multicomp 功能描述:SOCKET, PCB, DC POWER; Gender:Receptacle; Connector Mounting:PCB; Contact Termination:Through Hole Vertical; Connector Mounting Orientation:PCB; Connector Type:Standard Power Entry ;RoHS Compliant: Yes
MJ8250FE 制造商:Ohmite Mfg Co 功能描述:
MJ8251F 制造商:Ohmite Mfg Co 功能描述:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*