- 您現在的位置：買賣IC網 > PDF目錄367625 > MPT612FBD48 (NXP SEMICONDUCTORS) Maximum power point tracking IC PDF資料下載
參數資料
| 型號： | MPT612FBD48 |
| 廠商： | NXP SEMICONDUCTORS |
| 元件分類： | 模擬信號調理 |
| 英文描述： | Maximum power point tracking IC |
| 中文描述： | SPECIALTY ANALOG CIRCUIT, PQFP48 |
| 封裝： | 7 X 7 MM, 1.40 MM HEIGHT, PLASTIC, MS-026, SOT313-2, LQFP-48 |
| 文件頁數： | 11/37頁 |
| 文件大小： | 607K |
| 代理商： | MPT612FBD48 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁當前第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁
NXP Semiconductors
MPT612
Maximum power point tracking IC
from the interrupt vector location. If more than one request is assigned to the FIQ class,
the FIQ service routine reads a word from the VIC that identifies which FIQ sources are
requesting an interrupt.
Vectored IRQs have the middle priority. Sixteen of the interrupt requests can be assigned
to this category. Any of the interrupt requests can be assigned to any of the 16 vectored
IRQ slots. Slot 0 has the highest priority and slot 15 has the lowest priority.
Non-vectored IRQs have the lowest priority.
The VIC combines the requests from all the vectored and non-vectored IRQs to generate
the IRQ signal for the ARM processor. The IRQ service routine can start by reading a
register from the VIC and jumping to it. If any vectored IRQs are pending, the VIC
provides the address of the highest priority requesting IRQs service routine, otherwise it
provides the address of a default routine which is shared by all the non-vectored IRQs.
The default routine can read another VIC register to see which IRQs are active.
7.5.1 Interrupt sources
Each peripheral device has one interrupt line connected to the VIC which can contain
several internal interrupt flags. Each individual interrupt flag can represent more than one
interrupt source.
7.6 Pin connect block
The pin connect block enables selected device pins to have more than one function.
Configuration registers control the multiplexers to allow connection between the pin and
the on chip peripherals. Peripherals should be connected to the appropriate pins before
being activated and any related interrupt(s) are enabled. Activity of any enabled
peripheral function that is not mapped to a related pin should be considered undefined.
The pin control module with its pin select registers defines the functionality of the
processor core in a given hardware environment.
After reset, all pins of PIO are configured as inputs with the following exception:
If the JTAGSEL pin is HIGH (Debug mode enabled), the JTAG pins will assume their
JTAG functionality for use with EmbeddedICE and cannot be configured via the pin
connect block.
7.7 Fast general purpose parallel I/O
Pins that are not connected to a specific peripheral function are controlled by the GPIO
registers. Pins can be dynamically configured as inputs or outputs. Separate registers
allow simultaneous setting or clearing any number of outputs. The value of the output
register and the state of the port pins can be read back. The GPIO provides the following
features:
GPIO registers are relocated for the fastest possible I/O timing
Mask registers allow sets of port bits to be treated as a group, leaving other bits
unchanged
All GPIO registers are byte addressable
Entire port value can be written in one instruction
Bit level set and clear registers allow a single instruction setting or clearing of any
number of bits on one port
Direction control of individual bits
MPT612
All information provided in this document is subject to legal disclaimers.
NXP B.V. 2010. All rights reserved.
Product data sheet
Rev. 2 — 14 September 2010
11 of 11
相關PDF資料 |
PDF描述 |
|---|---|
| MX0912B251Y | NPN microwave power transistor |
| MX0912B251Y | NPN microwave power transistor |
| MX0912B251Y | NPN microwave power transistor |
| MX0912B251Y | NPN microwave power transistor |
| MX0912B251Y | NPN microwave power transistor |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MPT612FBD48,151 | 功能描述:ARM微控制器 - MCU 32b 32K Flash 28I/O RoHS:否 制造商:STMicroelectronics 核心:ARM Cortex M4F 處理器系列:STM32F373xx 數據總線寬度:32 bit 最大時鐘頻率:72 MHz 程序存儲器大小:256 KB 數據 RAM 大小:32 KB 片上 ADC:Yes 工作電源電壓:1.65 V to 3.6 V, 2 V to 3.6 V, 2.2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:LQFP-48 安裝風格:SMD/SMT |
| MPT612FBD48151 | 制造商:Rochester Electronics LLC 功能描述: 制造商:NXP 功能描述: 制造商:NXP Semiconductors 功能描述: |
| MPT6-150 | 制造商:Powerfilm Inc 功能描述:Flexible Thin-Film Solar Module, 6.0V @ 100mA |
| MPT-65 | 制造商:MEANWELL 制造商全稱:Mean Well Enterprises Co., Ltd. 功能描述:65W Triple Output Medical Type |
| MPT-65_11 | 制造商:MEANWELL 制造商全稱:Mean Well Enterprises Co., Ltd. 功能描述:65W Triple Output Medical Type |
發布緊急采購，3分鐘左右您將得到回復。