參數資料
型號： MQ80C154-20P883
廠商： ATMEL CORP
元件分類： 微控制器/微處理器
英文描述： 8-BIT, 20 MHz, MICROCONTROLLER, CQFP44
封裝： CERAMIC, QFP-44
文件頁數： 57/101頁
文件大?。?/td> 3398K
代理商： MQ80C154-20P883
82
8168C-MCU Wireless-02/10
AT86RF212
6.5 Energy Detection (ED)
The Energy Detection (ED) module is characterized by:
a dynamic range of 87 dB
a resolution of about 1 dB
a measurement time of 8 symbol periods for IEEE 802.15.4 compliant data rates
6.5.1 Overview
The receiver ED measurement (ED scan procedure) can be used as a part of a channel
selection algorithm. It is an estimation of the received signal power within the bandwidth
of an IEEE 802.15.4 channel. No attempt is made to identify or decode signals on the
channel. The ED value is calculated by averaging RSSI values over 8 symbol periods,
with the exception of the High Data Rate Modes (refer to section 7.1.4).
6.5.2 Measurement Description
There are two ways to initiate an ED measurement,
manually by writing an arbitrary value to register 0x07 (PHY_ED_LEVEL), or
automatically after detection of a valid SHR of an incoming frame.
Manually:
For manually initiated ED measurements, the radio transceiver needs to be
either in the state RX_ON or BUSY_RX. The end of the ED measurement time
(8 symbol periods) is indicated by the interrupt IRQ_4 (CCA_ED_DONE) and
the measurement result is stored in register 0x07 (PHY_ED_LEVEL).
In order to avoid interference with an automatically initiated ED measurement,
the SHR detection can be disabled by setting register bit RX_PDT_DIS
(register 0x15, RX_SYN), refer to section 7.2.
Note that it is not recommended to manually initiate an ED measurement when
using the Extended Operating Mode.
Automatically:
An automated ED measurement is started upon SHR detection. The end of the
automated measurement is not signaled by an interrupt.
When using the Basic Operating Mode and standard compliant data rates, a
valid ED value (register 0x07, PHY_ED_LEVEL) of the currently received frame
is accessible not later than 8 symbol periods after IRQ_2 (RX_START) plus a
processing time of 12 s. For High Data Rate Modes (refer to 7.1.4), the
measurement duration is reduced to 2 symbol periods plus a processing time of
12 s. The ED value remains valid until a new RX_START interrupt is
generated by the next incoming frame or until another ED measurement is
initiated.
When using the Extended Operating Mode, it is useful to mask IRQ_2
(RX_START), thus the interrupt cannot be used as timing reference. A
successful frame reception is signalized by interrupt IRQ_3 (TRX_END). In this
case, the ED value needs to be read within the time span of a next SHR
detection plus the ED measurement time in order to avoid overwrite of the
current ED value.
相關PDF資料
PDF描述
IR80C52CXXX-12:RD 8-BIT, MROM, 12 MHz, MICROCONTROLLER, CQCC44
IS83C154TXXX-25D 8-BIT, MROM, 25 MHz, MICROCONTROLLER, PQCC44
IF180C52EXXX-L16:R 8-BIT, MROM, 16 MHz, MICROCONTROLLER, PQFP44
MQ80C52CXXX-20/883R 8-BIT, MROM, 20 MHz, MICROCONTROLLER, CQFP44
MJ80C31U-36:D MICROCONTROLLER
相關代理商/技術參數
參數描述
MQ80C154-25 制造商:TEMIC 制造商全稱:TEMIC Semiconductors 功能描述:CMOS 0 to 36 MHz Single Chip 8-bit Microcontroller
MQ80C154-30 制造商:TEMIC 制造商全稱:TEMIC Semiconductors 功能描述:CMOS 0 to 36 MHz Single Chip 8-bit Microcontroller
MQ80C154-36 制造商:TEMIC 制造商全稱:TEMIC Semiconductors 功能描述:CMOS 0 to 36 MHz Single Chip 8-bit Microcontroller
MQ80C154-L16 制造商:TEMIC 制造商全稱:TEMIC Semiconductors 功能描述:CMOS 0 to 36 MHz Single Chip 8-bit Microcontroller
MQ80C186-10/BYA 制造商:Rochester Electronics LLC 功能描述:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*