參數資料
型號: MQ80C154-20P883
廠商: ATMEL CORP
元件分類: 微控制器/微處理器
英文描述: 8-BIT, 20 MHz, MICROCONTROLLER, CQFP44
封裝: CERAMIC, QFP-44
文件頁數: 82/101頁
文件大?。?/td> 3398K
代理商: MQ80C154-20P883
104
Figure 7-4 to Figure 7-8 illustrate typical spectra of the transmitted signals of the
AT86RF212 and do not claim any limits.
Refer to the local authority bodies (FCC, ETSI, etc.) for further details about definition of
power spectral density masks, definition of spurious emission, allowed modulation
bandwidth, transmit power, and its limits.
7.3.4 TX Output Power
The maximum output power of the transmitter is typically 5 dBm in normal mode and 10
dBm in boost mode. The TX output power can be set via register bits TX_PWR (register
0x05, PHY_TX_PWR). The output power of the transmitter can be controlled down to
-11 dBm dB with 1 dB resolution.
To meet the spectral requirements of the European and Chinese bands, it is necessary
to limit the TX power by appropriate setting of TX_PWR, GC_PA (register 0x05,
PHY_TX_PWR), and GC_TX_OFFS (register 0x16, TX_CTRL_0). See Table 7-15 and
Table 7-16 for recommended values.
7.3.5 TX Power Ramping
To optimize the output power spectral density (PSD), individual transmitter blocks are
enabled sequentially. A transmit action is started by either the rising edge of pin
SLP_TR or the command TX_START in register 0x02. One symbol period later the data
transmission begins. During this time period, the PLL settles to the frequency used for
transmission. The PA is enabled prior to the data transmission start. This PA lead time
can be adjusted with the value PA_LT in register 0x16 (RF_CTRL_0). The PA is always
enabled at the lowest gain value corresponding to GC_PA = 0. Then the PA gain is
increased automatically to the value set by GC_PA in register 0x16 (RF_CTRL_0). After
transmission is completed, TX power ramping down is performed in an inverse order.
The control signals associated with TX power ramping are shown in Figure 7-9. In this
example, the transmission is initiated with the rising edge of pin 11 (SLP_TR). The radio
transceiver state changes from PLL_ON to BUSY_TX.
Figure 7-9. TX Power Ramping Example (O-QPSK 250 kbit/s Mode)
Using an external RF front-end (refer to section 9.4), it may be required to adjust the
startup time of the external PA relative to the internal building blocks to optimize the
overall PSD. This can be achieved using register bits PA_LT (register 0x16,
RF_CTRL_0).
AT86RF212
8168C-MCU Wireless-02/10
相關PDF資料
PDF描述
IR80C52CXXX-12:RD 8-BIT, MROM, 12 MHz, MICROCONTROLLER, CQCC44
IS83C154TXXX-25D 8-BIT, MROM, 25 MHz, MICROCONTROLLER, PQCC44
IF180C52EXXX-L16:R 8-BIT, MROM, 16 MHz, MICROCONTROLLER, PQFP44
MQ80C52CXXX-20/883R 8-BIT, MROM, 20 MHz, MICROCONTROLLER, CQFP44
MJ80C31U-36:D MICROCONTROLLER
相關代理商/技術參數
參數描述
MQ80C154-25 制造商:TEMIC 制造商全稱:TEMIC Semiconductors 功能描述:CMOS 0 to 36 MHz Single Chip 8-bit Microcontroller
MQ80C154-30 制造商:TEMIC 制造商全稱:TEMIC Semiconductors 功能描述:CMOS 0 to 36 MHz Single Chip 8-bit Microcontroller
MQ80C154-36 制造商:TEMIC 制造商全稱:TEMIC Semiconductors 功能描述:CMOS 0 to 36 MHz Single Chip 8-bit Microcontroller
MQ80C154-L16 制造商:TEMIC 制造商全稱:TEMIC Semiconductors 功能描述:CMOS 0 to 36 MHz Single Chip 8-bit Microcontroller
MQ80C186-10/BYA 制造商:Rochester Electronics LLC 功能描述: