參數資料
型號: MULTISYNCFE750
英文描述: Monitor_ICs:HD6433577 LA7841 BA9761F MQ571 XC13289LSP LSC3820P2 uPD61882A
中文描述: Monitor_ICs:HD6433577 LA7841 BA9761F MQ571 XC13289LSP LSC3820P2 uPD61882A
文件頁數: 40/52頁
文件大小: 517K
代理商: MULTISYNCFE750
40
MON08 Multilink User Manual
P&E
Microcomputer
Systems, Inc.
MON08 MULTILINK
power supply on and off. The use will also be prompted to turn power
on and off to reset the target processor, as the PC doesn’t have control
of the target reset. Turning off the power supply is necessary mainly to
be able to pass the initial security mode check and access the flash on
the processor. A simple reset is not enough; to pass the security check,
you must first force the processor to encounter a POR (power-on reset)
which requires that the processor’s voltage dip below 0.1v. Once
security has been passed, resetting the device or re-entering the
software should be easier. This configuration can be specified at startup
in the software by using the
NODTR
command-line parameter;
otherwise the software will remember the hardware configuration from
session to session. The Class III selection also applies to use of the ICS
board with the two-pin blank part programming connector.
Class IV
Custom Board (no ICS) with MON08 serial port circuitry and
additional auto-reset circuit built in. In this configuration, the ICS
board is not used at all. The user must provide a serial port connection
from the PC and all hardware configuration necessary to force the
processor into MON08 mode upon reset. In addition, the user must
include an extra circuit which allows the reset line of the processor to
be driven low from the DTR line of the serial port connector (Pin 4 on a
DB9). The following diagram shows the additional connection needed
to reset from a DB9 serial connector.
Figure 4-37: Additional Connection To Reset From DB9
In this configuration, because the software does not directly control power to
the processor, the user will be prompted to turn the processor’s power supply
on and off. Turning off thepower supply is necessary in order to be able to pass
the initial security mode check and access the flash on the processor. A simple
reset is not enough; to pass the security check, you must first force the
processor to encounter a POR (power-on reset) which requires the processor’s
voltage to dip below 0.1v. Once security has been passed, resetting the device
相關PDF資料
PDF描述
MUM8128W-17 x8 EPROM
MUM8128W-20 x8 EPROM
MUM8128W-25 x8 EPROM
MUM8128WI-17 x8 EPROM
MUM8128WI-20 x8 EPROM
相關代理商/技術參數
參數描述
MULTI-TC 制造商:ERSA 功能描述:SOLDERING IRON 230V 75W EURO PLUG 制造商:ERSA 功能描述:SOLDERING IRON, 230V, 75W, EURO PLUG
MULTI-TEST 制造商:L COM 功能描述:PC CABLE TESTER ATA 制造商:L-com Inc 功能描述:PC CABLE TESTER ATA
MULTI-USE LIGHT 制造商:Energizer Battery Company 功能描述:
MULTIWATT 制造商:未知廠家 制造商全稱:未知廠家 功能描述:MULTIWATT
MULTIWATT11 制造商:未知廠家 制造商全稱:未知廠家 功能描述:MULTIWATT