- 您現在的位置：買賣IC網 > PDF目錄359238 > MULTISYNCFE750 Monitor_ICs:HD6433577 LA7841 BA9761F MQ571 XC13289LSP LSC3820P2 uPD61882A PDF資料下載
參數資料
| 型號： | MULTISYNCFE750 |
| 英文描述： | Monitor_ICs:HD6433577 LA7841 BA9761F MQ571 XC13289LSP LSC3820P2 uPD61882A |
| 中文描述： | Monitor_ICs：HD6433577 LA7841 BA9761F MQ571 XC13289LSP LSC3820P2 uPD61882A |
| 文件頁數： | 50/52頁 |
| 文件大?。?/td> | 517K |
| 代理商： | MULTISYNCFE750 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁當前第50頁第51頁第52頁
50
MON08 Multilink User Manual
P&E
Microcomputer
Systems, Inc.
MON08 MULTILINK
Type”. If you are connecting to a class II board, check the “MON08
cable communication connections type” in the “advanced settings”
dialog.
4 – Device entered monitor mode:
Once the software has received, or failed to receive, a break from the
processor, it attempts to communicate with the monitor running on the
68HC08 processor. It tries to read the monitor version number by issuing a
monitor mode read. If the processor fails to respond properly to this
command, this flag will be ‘N’.
5 – Reset was Power-On Reset:
If the device properly entered monitor mode (4), the software will read the
reset status register (RSR). This read does not affect the security sequence,
and occurs purely for diagnostic reasons. The reset status register indicates
the conditions under which the processor underwent the last reset. For the
software to pass the security check properly, it MUST first cause the
processor to undergo a Power-On Reset. The software reads the reset status
register to determine if the last reset was indeed caused by power-on. The
result of the reset status register is indicated in parentheses after the flag
value. If the highest bit is not set then the reset was not a power on reset,
and the flag will indicate ‘N’. Reasons for this include:
1. The processor did not power all the way down because power was
being supplied to the processor through either the port pins, IRQ line,
RESET line, or power pins.
2. The voltage driven on the power pin of the processor did not go
below 0.1 volts.
3. The processor was not reset properly. Check the “Target Hardware
Type”. If you are connecting to a class II board, check the “MON08
cable communication connections type” in the “advanced settings”
dialog.
6 – ROM is accessible (un-secured):
If the device properly entered monitor mode (4), the software reads
locations $FFF6-$FFFF to determine if the processor passes the security
check. Memory locations which are invalid or protected read back from the
device as $AD. If all bytes from $FFF6-$FFFF read a value of $AD, it is
assumed the device is secure, and the flag value is an ‘N’. If all flags 0-5
register a value of ‘Y’ and flag 6 register a value of ‘N,’ then the reset
process has gone correctly except that the security code used to pass
security was incorrect. Specify the correct security code and try again, or
IGNORE the security failure and erase the device. Once you erase a
secured device, you must exit the software and restart it in order to pass
相關PDF資料 |
PDF描述 |
|---|---|
| MUM8128W-17 | x8 EPROM |
| MUM8128W-20 | x8 EPROM |
| MUM8128W-25 | x8 EPROM |
| MUM8128WI-17 | x8 EPROM |
| MUM8128WI-20 | x8 EPROM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MULTI-TC | 制造商:ERSA 功能描述:SOLDERING IRON 230V 75W EURO PLUG 制造商:ERSA 功能描述:SOLDERING IRON, 230V, 75W, EURO PLUG |
| MULTI-TEST | 制造商:L COM 功能描述:PC CABLE TESTER ATA 制造商:L-com Inc 功能描述:PC CABLE TESTER ATA |
| MULTI-USE LIGHT | 制造商:Energizer Battery Company 功能描述: |
| MULTIWATT | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:MULTIWATT |
| MULTIWATT11 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:MULTIWATT |
發布緊急采購，3分鐘左右您將得到回復。