- 您現在的位置：買賣IC網 > PDF目錄368232 > PSD813F4 Flash In System Programmable Mirocomputer Peripherals(閃速，在系統可編程微控制器外圍器件，1M位閃速存儲器，256K位EEPROM，16K位SRAM) PDF資料下載
參數資料
| 型號： | PSD813F4 |
| 英文描述： | Flash In System Programmable Mirocomputer Peripherals(閃速，在系統可編程微控制器外圍器件，1M位閃速存儲器，256K位EEPROM，16K位SRAM) |
| 中文描述： | Flash在系統可編程Mirocomputer外設（閃速，在系統可編程微控制器外圍器件，100萬位閃速存儲器，256K位的EEPROM，16K的位的SRAM） |
| 文件頁數： | 26/130頁 |
| 文件大?。?/td> | 650K |
| 代理商： | PSD813F4 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁當前第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁
PSD813F Famly
Prelimnary
22
9.1.1.6 Writing to the Optional EEPROM
Data may be written a byte at a time to the EEPROM using simple write operations, much
like writing to an SRAM. Unlike SRAM though, the completion of each byte write must be
checked before the next byte is written. To speed up this process, the PSD813F offers a
Page write feature to allow writing of several bytes before checking status.
To prevent inadvertent writes to EEPROM, the PSD813F offers a Software Data Protect
(SDP) mode. Once enabled, SDP forces the MCU to “unlock” the EEPROM before altering
its contents, much like Flash memory programming.
9.1.1.6.1 Write a Byte to EEPROM
A write operation is initiated when an EEPROM select signal (EESi) is true and the write
strobe signal (wr) into the PSD813F is true. If the PSD813F detects no additional writes
within 120 μsec, an internal storage operation is initiated. Internal storage to EEPROM
memory technology typically takes a few milliseconds to complete.
The status of the write operation is obtained by the MCU reading the Data Polling or Toggle
bits (as detailed in section 9.1.1.5), or the Ready/Busy output pin (section 9.1.1.2).
Keep in mind that the MCU does not need to erase a location in EEPROM before writing it.
Erasure is performed automatically as an internal process.
9.1.1.6.2 Write a Page to EEPROM
Writing data to EEPROM using page mode is more efficient than writing one byte at a
time. The PSD813F EEPROM has a 64 byte volatile buffer that the MCU may fill before an
internal EEPROM storage operation is initiated. Page mode timing approaches a 64:1
advantage over the time it takes to write individual bytes.
To invoke page mode, the MCU must write to EEPROM locations within a single page, with
no more than 120 μsec between individual byte writes. A single page means that address
lines A14 to A6 must remain constant. The MCU may write to the 64 locations on a page in
any order, which is determined by address lines A5 to A0. As soon as 120 μsec have
expired after the last page write, the internal EEPROM storage process begins and the
MCU checks programming status. Status is checked the same way it is for byte writes,
described above.
Note:
be aware that if the upper address bits (A14 to A6) change during page write
operations, loss of data may occur. Ensure that all bytes for a given page have
been successfully stored in the EEPROM before proceeding to the next page. Correct
management of MCU interrupts during EEPROM page write operations is essential.
9.1.1.6.3 EEPROM Software Data Protect (SDP)
The SDP feature is useful for protecting the contents of EEPROM from inadvertent write
cycles that may occur during uncontrolled MCU bus conditions. These may happen if the
application software gets lost or when V
CC
is not within normal operating range.
Instructions from the MCU are used to enable and disable SDP mode (see Table 9). Once
enabled, the MCU must write an instruction sequence to EEPROM before writing data
(much like writing to Flash memory). SDP mode can be used for both byte and page writes
to EEPROM. The device will remain in SDP mode until the MCU issues a valid SDP disable
instruction.
PSD813F devices are shipped with SDP mode disabled. However, within PSDsoft, SDP
mode may be enabled as part of programming the device with a device programmer
(PSDpro).
The
PSD813F
Functional
Blocks
(cont.)
相關PDF資料 |
PDF描述 |
|---|---|
| PSD813F | Flash In-System-Programmable Microcontroller Peripherals(閃速，在系統可編程微控制器外圍器件，1M位閃速存儲器，256K位EEPROM，16K位SRAM) |
| PSD813FH(中文) | Field Programmble Microcontroller Peripherals With Flash Memory(帶閃存的現場可編程微控制器) |
| PSD813FN(中文) | Field Programmble Microcontroller Peripherals(帶閃存的現場可編程微控制器) |
| PSD813FN | Field Programmble Microcontroller Peripherals(帶閃存的現場可編程微控制器) |
| PSD813FH | Field Programmble Microcontroller Peripherals With Flash Memory(帶閃存的現場可編程微控制器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PSD813F4-15J | 制造商:WSI 功能描述: |
| PSD813F4-15JI | 制造商:WSI 功能描述: |
| PSD813F4A-90J | 功能描述:SPLD - 簡單可編程邏輯器件 U 511-PSD813F2A-90J RoHS:否 制造商:Texas Instruments 邏輯系列:TICPAL22V10Z 大電池數量:10 最大工作頻率:66 MHz 延遲時間:25 ns 工作電源電壓:4.75 V to 5.25 V 電源電流:100 uA 最大工作溫度:+ 75 C 最小工作溫度:0 C 安裝風格:Through Hole 封裝 / 箱體:DIP-24 |
| PSD813F4A-90M | 功能描述:SPLD - 簡單可編程邏輯器件 U 511-PSD813F2A-90M RoHS:否 制造商:Texas Instruments 邏輯系列:TICPAL22V10Z 大電池數量:10 最大工作頻率:66 MHz 延遲時間:25 ns 工作電源電壓:4.75 V to 5.25 V 電源電流:100 uA 最大工作溫度:+ 75 C 最小工作溫度:0 C 安裝風格:Through Hole 封裝 / 箱體:DIP-24 |
| PSD813F4VA-15J | 功能描述:SPLD - 簡單可編程邏輯器件 U 511-PSD813F2VA-15J RoHS:否 制造商:Texas Instruments 邏輯系列:TICPAL22V10Z 大電池數量:10 最大工作頻率:66 MHz 延遲時間:25 ns 工作電源電壓:4.75 V to 5.25 V 電源電流:100 uA 最大工作溫度:+ 75 C 最小工作溫度:0 C 安裝風格:Through Hole 封裝 / 箱體:DIP-24 |
發布緊急采購，3分鐘左右您將得到回復。