參數資料
型號： PSD813F4
英文描述： Flash In System Programmable Mirocomputer Peripherals(閃速，在系統可編程微控制器外圍器件，1M位閃速存儲器，256K位EEPROM，16K位SRAM)
中文描述： Flash在系統可編程Mirocomputer外設（閃速，在系統可編程微控制器外圍器件，100萬位閃速存儲器，256K位的EEPROM，16K的位的SRAM）
文件頁數： 30/130頁
文件大?。?/td> 650K
代理商： PSD813F4
PSD813F Famly
Prelimnary
26
9.1.1.7.2 Data Toggle
Checking the Data Toggle bit on DQ6 is a method of determining whether a Program or
Erase instruction is in progress or has completed. Figure 6 shows the Data Toggle
algorithm.
When the MCU issues a programming instruction, the embedded algorithm within the
PSD813F begins. The MCU then reads the location of the byte to be programmed in
Flash to check status. Data bit DQ6 of this location will toggle each time the MCU reads
this location until the embedded algorithm is complete. The MCU continues to read this
location, checking DQ6 and monitoring the Error bit on DQ5. When DQ6 stops toggling
(two consecutive reads yield the same value), and the Error bit on DQ5 remains ‘0’, then
the embedded algorithm is complete. If the Error bit on DQ5 is ‘1’, the MCU should test
DQ6 again, since DQ6 may have changed simultaneously with DQ5 (see Figure 6).
The Error bit at DQ5 will be set if either an internal timeout occurred while the embedded
algorithm attempted to program the byte, or if the MCU attempted to program a ‘1’ to a bit
that was not erased (not erased is logic ‘0’).
It is suggested (as with all Flash memories) to read the location again after the embedded
programming algorithm has completed to compare the byte that was written to Flash with
the byte that was intended to be written.
When using the Data Toggle method after an erase instructin, Figure 6 still applies. DQ6 will
toggle until the erase operation is complete. A ‘1’ on DQ5 will indicate a timeout failure of
the erase operation, a ‘0’ indicates no error. The MCU can read any location within the
sector being erased to get DQ6 and DQ5.
PSDsoft will generate ANSI C code functions which implement these Data Toggling
algorithms.
The
PSD813F
Functional
Blocks
(cont.)
Figure 6. Data Toggle Flow Chart
START
READ
DQ5 & DQ6
NO
YES
NO
YES
YES
NO
=
TOGGLE
DQ5
=1
=
TOGGLE
READ DQ6
FAIL
PASS
相關PDF資料
PDF描述
PSD813F Flash In-System-Programmable Microcontroller Peripherals(閃速，在系統可編程微控制器外圍器件，1M位閃速存儲器，256K位EEPROM，16K位SRAM)
PSD813FH(中文) Field Programmble Microcontroller Peripherals With Flash Memory(帶閃存的現場可編程微控制器)
PSD813FN(中文) Field Programmble Microcontroller Peripherals(帶閃存的現場可編程微控制器)
PSD813FN Field Programmble Microcontroller Peripherals(帶閃存的現場可編程微控制器)
PSD813FH Field Programmble Microcontroller Peripherals With Flash Memory(帶閃存的現場可編程微控制器)
相關代理商/技術參數
參數描述
PSD813F4-15J 制造商:WSI 功能描述:
PSD813F4-15JI 制造商:WSI 功能描述:
PSD813F4A-90J 功能描述:SPLD - 簡單可編程邏輯器件 U 511-PSD813F2A-90J RoHS:否 制造商:Texas Instruments 邏輯系列:TICPAL22V10Z 大電池數量:10 最大工作頻率:66 MHz 延遲時間:25 ns 工作電源電壓:4.75 V to 5.25 V 電源電流:100 uA 最大工作溫度:+ 75 C 最小工作溫度:0 C 安裝風格:Through Hole 封裝 / 箱體:DIP-24
PSD813F4A-90M 功能描述:SPLD - 簡單可編程邏輯器件 U 511-PSD813F2A-90M RoHS:否 制造商:Texas Instruments 邏輯系列:TICPAL22V10Z 大電池數量:10 最大工作頻率:66 MHz 延遲時間:25 ns 工作電源電壓:4.75 V to 5.25 V 電源電流:100 uA 最大工作溫度:+ 75 C 最小工作溫度:0 C 安裝風格:Through Hole 封裝 / 箱體:DIP-24
PSD813F4VA-15J 功能描述:SPLD - 簡單可編程邏輯器件 U 511-PSD813F2VA-15J RoHS:否 制造商:Texas Instruments 邏輯系列:TICPAL22V10Z 大電池數量:10 最大工作頻率:66 MHz 延遲時間:25 ns 工作電源電壓:4.75 V to 5.25 V 電源電流:100 uA 最大工作溫度:+ 75 C 最小工作溫度:0 C 安裝風格:Through Hole 封裝 / 箱體:DIP-24
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*