- 您現在的位置：買賣IC網 > PDF目錄192305 > S71GL064A08BAW0F3 (SPANSION LLC) Stacked Multi-Chip Product (MCP) Flash Memory and RAM PDF資料下載
參數資料
| 型號： | S71GL064A08BAW0F3 |
| 廠商： | SPANSION LLC |
| 元件分類： | 存儲器 |
| 英文描述： | Stacked Multi-Chip Product (MCP) Flash Memory and RAM |
| 中文描述： | SPECIALTY MEMORY CIRCUIT, PBGA56 |
| 封裝： | 7 X 9 MM, 1.20 MM HEIGHT, LEAD FREE, FBGA-56 |
| 文件頁數： | 90/134頁 |
| 文件大?。?/td> | 2383K |
| 代理商： | S71GL064A08BAW0F3 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁當前第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁
February 8, 2005 S71GL064A_00_A2
S71GL064A based MCPs
57
Advance
Informatio n
DQ2: Toggle Bit II
The “Toggle Bit II” on DQ2, when used with DQ6, indicates whether a particular sector is ac-
tively erasing (that is, the Embedded Erase algorithm is in progress), or whether that sector
is erase-suspended. Toggle Bit II is valid after the rising edge of the final WE# pulse in the
command sequence.
DQ2 toggles when the system reads at addresses within those sectors that have been se-
lected for erasure. (The system may use either OE# or CE# to control the read cycles.) But
DQ2 cannot distinguish whether the sector is actively erasing or is erase-suspended. DQ6, by
comparison, indicates whether the device is actively erasing, or is in Erase Suspend, but can-
not distinguish which sectors are selected for erasure. Thus, both status bits are required for
sector and mode information. Refer to Table 11 to compare outputs for DQ2 and DQ6.
Figure 8 shows the toggle bit algorithm in flowchart form, and the section “DQ2: Toggle Bit
II” explains the algorithm. See also the RY/BY#: Ready/Busy# subsection. Figure 20 shows
the toggle bit timing diagram. Figure 21 shows the differences between DQ2 and DQ6 in
graphical form.
Reading Toggle Bits DQ6/DQ2
Refer to Figure 8 for the following discussion. Whenever the system initially begins reading
toggle bit status, it must read DQ7–DQ0 at least twice in a row to determine whether a toggle
bit is toggling. Typically, the system would note and store the value of the toggle bit after the
first read. After the second read, the system would compare the new value of the toggle bit
with the first. If the toggle bit is not toggling, the device has completed the program or erase
operation. The system can read array data on DQ7–DQ0 on the following read cycle.
However, if after the initial two read cycles, the system determines that the toggle bit is still
toggling, the system also should note whether the value of DQ5 is high (see the section on
DQ5). If it is, the system should then determine again whether the toggle bit is toggling, since
the toggle bit may have stopped toggling just as DQ5 went high. If the toggle bit is no longer
toggling, the device has successfully completed the program or erase operation. If it is still
toggling, the device did not completed the operation successfully, and the system must write
the reset command to return to reading array data.
The remaining scenario is that the system initially determines that the toggle bit is toggling
and DQ5 has not gone high. The system may continue to monitor the toggle bit and DQ5
through successive read cycles, determining the status as described in the previous para-
graph. Alternatively, it may choose to perform other system tasks. In this case, the system
must start at the beginning of the algorithm when it returns to determine the status of the
operation (top of Figure 6).
DQ5: Exceeded Timing Limits
DQ5 indicates whether the program, erase, or write-to-buffer time has exceeded a specified
internal pulse count limit. Under these conditions DQ5 produces a “1,” indicating that the pro-
gram or erase cycle was not successfully completed.
The device may output a “1” on DQ5 if the system tries to program a “1” to a location that
was previously programmed to “0.” Only an erase operation can change a “0” back to a
“1.” Under this condition, the device halts the operation, and when the timing limit has been
exceeded, DQ5 produces a “1.”
In all these cases, the system must write the reset command to return the device to the read-
ing the array (or to erase-suspend-read if the device was previously in the erase-suspend-
program mode).
相關PDF資料 |
PDF描述 |
|---|---|
| S71GL064A08BFI0B2 | Stacked Multi-Chip Product (MCP) Flash Memory and RAM |
| S71GL064A08BFI0B3 | Stacked Multi-Chip Product (MCP) Flash Memory and RAM |
| S71GL064A08BFI0F3 | Stacked Multi-Chip Product (MCP) Flash Memory and RAM |
| S71GL064A08BFW0B2 | Stacked Multi-Chip Product (MCP) Flash Memory and RAM |
| S71GL064A08BFW0B3 | Stacked Multi-Chip Product (MCP) Flash Memory and RAM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| S71GL064A08BFI0B0 | 制造商:SPANSION 制造商全稱:SPANSION 功能描述:Stacked Multi-Chip Product (MCP) Flash Memory and RAM |
| S71GL064A08BFI0B2 | 制造商:SPANSION 制造商全稱:SPANSION 功能描述:Stacked Multi-Chip Product (MCP) Flash Memory and RAM |
| S71GL064A08BFI0B3 | 制造商:SPANSION 制造商全稱:SPANSION 功能描述:Stacked Multi-Chip Product (MCP) Flash Memory and RAM |
| S71GL064A08BFI0F0 | 制造商:SPANSION 制造商全稱:SPANSION 功能描述:Stacked Multi-Chip Product (MCP) Flash Memory and RAM |
| S71GL064A08BFI0F2 | 制造商:SPANSION 制造商全稱:SPANSION 功能描述:Stacked Multi-Chip Product (MCP) Flash Memory and RAM |
發布緊急采購，3分鐘左右您將得到回復。