- 您現在的位置：買賣IC網 > PDF目錄3764 > SC28C94A1A,518 (NXP Semiconductors)IC UART QUAD W/FIFO 52-PLCC PDF資料下載
參數資料
| 型號： | SC28C94A1A,518 |
| 廠商： | NXP Semiconductors |
| 文件頁數： | 29/39頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC UART QUAD W/FIFO 52-PLCC |
| 產品培訓模塊： | Stand-Alone UARTs |
| 標準包裝： | 1 |
| 特點： | 故障啟動位檢測 |
| 通道數： | 4，QUART |
| FIFO's： | 8 字節 |
| 電源電壓： | 5V |
| 帶自動流量控制功能： | 是 |
| 帶故障啟動位檢測功能： | 是 |
| 帶調制解調器控制功能： | 是 |
| 帶CMOS： | 是 |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 52-LCC（J 形引線） |
| 供應商設備封裝： | 52-PLCC（19.2x19.2） |
| 包裝： | 標準包裝 |
| 產品目錄頁面： | 828 (CN2011-ZH PDF) |
| 其它名稱： | 568-1114-6 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁當前第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁
Philips Semiconductors
Product data sheet
SC28C94
Quad universal asynchronous receiver/transmitter (QUART)
2006 Aug 09
35
through the most significant 6 bits. The result of this is that the
channel value does not ’bid’. However the logic is such that other
parts of the bid being equal the condition of the highest channel will
be captured in CIR. The increasing order of the channels is A, B, C,
D. Thus channel D is the ”strongest” of the four.
It could be that the giving the highest strength to channel D may,
from time to time, not be what would be most desired. Further it
may be desired to alter the authority of a channel’s bid. This may
be done by setting the Rx and/or Tx interrupt bits in MR0 and MR1
to values different than zero. This will have the effect of not allowing
the associated receiver or transmitter to bid until its FIFO reaches a
particular fill level. Although this compromises the idea of the
bidding interrupt scheme, it is entirely safe to use. In fact it is setting
of MR0 and MR1 interrupt bits to zero that causes the receiver to
stop bidding when it is empty and causes the transmitter to stop
bidding when it is full. Altering the MR0 and MR1 interrupt bits only
changes the level at which the Rx & Tx bidding is stopped.
See the “Interrupt Note on 28C94” which refers to the use of the MR
registers in controlling the Rx and Tx bidding.
In normal operation the character of an interrupt will be controlled by
the above registers in conjunction with the IMR (Interrupt Mask
Register (one for each DUART)) . The function of the IMR will be to
enable bidding of any particular source. Recall that the QUART has
18 functions which may generate an interrupt.
The format of the interrupt vector is controlled by the ICR[1:0] bits.
The formats are shown in Table 10. The purpose of the vector
modification is to allow the interrupting source (either channel or
type and channel) to direct the processor to appropriate service
routine. We have found that some users wish to use extremely tight
loops for the service routines and find the addition of several tests of
status bytes to be very ’expensive’ in processor time.
Table 10.
Configuration of Interrupt Vector for the QUART
BIT 7
BIT 6
BIT 5
BIT 4
BIT 3
BIT 2
BIT 1
BIT 0
Interrupt vector for
→
ICR[1 0] 00
INTERRUPT VECTOR FORMATS (Controlled by ICR[1:0])
ICR[1:0]=00
IVR[7:0]
Full interrupt vector
Interrupt vector for
→
ICR[1 0] 01
ICR[1:0]=01
IVR[7:2]
ICR[1:0]
Interrupt vector 6 MSBs
Channel number
Interrupt vector for
→
ICR[1 0] 10
ICR[1:0]=10
IVR[7:5]
ICR[4:2]
ICR[1:0]
Interrupt vector 3 MSBs
Interrupt type
Channel number
Interrupt vector for
→
ICR[1 0] 11 (I hibit)
ICR[1:0]=11 (Inhibit)
Inhibit vector output. (Set bus to FFh)
CURRENT INTERRUPT REGISTER FORMAT CIR[7:0]
Rx or Tx byte count
Interrupt type: R/Tx CT COS BRK
Channel number
INTERRUPT CONTROL REGISTER FORMAT ICR[0:7]
Interrupt threshold ICR[7:2]
Interrupt vector format
ICR[1:0]
NOTE ON QUART INTERFACE TO ITS
CONTROLLING PROCESSOR
The QUART, has been designed to interface in either the
synchronous interrupt environment (without DACKN) or the
asynchronous interrupt environment (with DACKN). The 80xxx
devices of Intel design are usually operated in a synchronous
interrupt mode while those of Motorola design, 68xxx devices,
operate in an asynchronous interrupt mode.
Note: Synchronous and asynchronous interrupt modes are not
in any way associated with synchronous or asynchronous data
transmission.
The QUART has been designed with the pins required to service
either interface. In general then it is probable that in any application
some of the interface pins will not be used. This note discusses
what is required for the ”text book” connections of the two methods.
It should be noted that features of either method are not mutually
exclusive.
The interface pins are all active low. (at VSS or ground) The pins
used for normal reading and writing to the QUART (the generation of
a bus cycle) are CEN (Chip Enable), RDN (Read Enable), WRN
(Write Enable). The pins used in the interrupt service are IRQN
(Interrupt Request), IACKN (Interrupt Acknowledge). The pin used
for data transfer is DACKN (Data Acknowledge). IRQN and DACKN
are open drain outputs.
DACKN signaling can be enabled or disabled via writing to address
27h or 26h respectively. Note that if DACKN is enabled that writing
to the QUART will occur on the falling edge of DACKN. The use of
hardware reset (required at power up) enables DACKN.
The Asynchronous Interface
Those familiar with 68xxx I/O will note the use of the two pins RDN
and WRN to be in conflict with 68xxx devices use of the one R/WN
pin. The R/WN must be inverted such that the R/WN may drive the
WRN input while the inversion of R/WN drives the RDN input. It is
good practice to condition the inversion of R/WN such that RDN will
not become active on the termination of a write to the QUART while
CEN is still asserted. These short periods of read could upset FIFO
pointers in the chip.
During a read of the QUART DACKN signals that valid data is on the
data bus. During a write to the QUART DACKN signals that data
placed on the bus by the control processor has been written to the
相關PDF資料 |
PDF描述 |
|---|---|
| SC16C754BIA68,518 | IC UART QUAD W/FIFO 68-PLCC |
| SC26C92C1N,602 | IC UART DUAL W/FIFO 40-DIP |
| SC28L91A1B,551 | IC UART SINGLE W/FIFO 44-PQFP |
| SC28L91A1B,528 | IC UART SINGLE W/FIFO 44PQFP |
| SC28L91A1A,529 | IC UART SINGLE W/FIFO 44-PLCC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SC28C94A1AB | 制造商:PHILIPS-SEMI 功能描述: |
| SC28C94A1N | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Quad universal asynchronous receiver/transmitter QUART |
| SC28C94A1N,112 | 功能描述:IC UART QUAD W/FIFO 48-DIP RoHS:是 類別:集成電路 (IC) >> 接口 - UART（通用異步接收器/發送器） 系列:- 標準包裝:250 系列:- 特點:* 通道數:2，DUART FIFO's:16 字節 規程:RS232，RS485 電源電壓:2.25 V ~ 5.5 V 帶并行端口:- 帶自動流量控制功能:是 帶IrDA 編碼器/解碼器:是 帶故障啟動位檢測功能:是 帶調制解調器控制功能:是 帶CMOS:是 安裝類型:表面貼裝 封裝/外殼:48-TQFP 供應商設備封裝:48-TQFP（7x7） 包裝:托盤 其它名稱:XR16L2551IM-F-ND |
| SC28L194 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Quad UART for 3.3V and 5V supply voltage |
| SC28L194A1A | 功能描述:UART 接口集成電路 3V-5V 4CH UART INTEL/MOT INTRF RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。