參數資料
型號: ST6228CN1
廠商: 意法半導體
英文描述: ER 3C 3#16S SKT RECP WALL
中文描述: 8位單片機與微控制器/ D轉換器,自動重加載定時器,UART的秘書長辦公室,安全復位和28引腳封裝
文件頁數: 13/84頁
文件大小: 561K
代理商: ST6228CN1
13/84
13
ST62T28C/E28C
2 CENTRAL PROCESSING UNIT
2.1 INTRODUCTION
The CPUCoreof ST6devicesisindependentofthe
I/O or Memory configuration. As such, it may be
thought of as an independent central processor
communicating with on-chip I/O, Memory and Pe-
ripherals via internal address, data, and control
buses. In-core communication is arranged as
shown in Figure 6; the controller being externally
linked to both the Reset and Oscillator circuits,
while thecore islinkedto thededicated on-chip pe-
ripherals via the serial data bus and indirectly, for
interrupt purposes, through the control registers.
2.2 CPU REGISTERS
TheST6FamilyCPUcorefeaturessixregistersand
three pairs of flags available to the programmer.
These are described in the following paragraphs.
Accumulator (A)
. The accumulator is an 8-bit
general purpose register used in all arithmetic cal-
culations, logical operations, and data manipula-
tions. The accumulator can be addressed in Data
space as a RAM locationat address FFh. Thus the
ST6 can manipulate the accumulator just like any
other register in Data space.
Indirect Registers (X, Y).
These two indirect reg-
isters are used as pointers to memory locations in
Data space. They are used in the register-indirect
addressing mode. These registers can be ad-
dressed in the data space as RAM locations at ad-
dresses 80h(X) and 81h (Y). They can also be ac-
cessed with the direct, shortdirect, orbit direct ad-
dressing modes. Accordingly, the ST6 instruction
set can usethe indirect registers as any other reg-
ister of the data space.
Short Direct Registers (V, W).
These two regis-
ters are used to save a byte in short direct ad-
dressing mode. They can be addressed in Data
space as RAM locations at addresses 82h (V) and
83h (W). They can also be accessed using the di-
rect and bit direct addressing modes. Thus, the
ST6 instruction set can use the short direct regis-
ters as any other register of the data space.
Program Counter (PC). The program counter is a
12-bit register which contains the address of the
next ROM location to be processed by the core.
This ROM location may be an opcode, an oper-
and, or the address of an operand. The 12-bit
length allows the direct addressing of 4096 bytes
in Program space.
Figure 6. ST6 Core Block Diagram
PROGRAM
RESET
OPCODE
FLAG
VALUES
2
CONTROLLER
FLAGS
ALU
A-DATA
B-DATA
ADDRESS/READ LINE
DATA SPACE
INTERRUPTS
DATA
RAM/EEPROM
DATA
ROM/EPROM
RESULTS TO DATA SPACE (WRITE LINE)
ROM/EPROM
DEDICATIONS
ACCUMULATOR
CONTROL
SIGNALS
OSCin
OSCout
ADDRESS
DECODER
256
12
Program Counter
and
6 LAYER STACK
0,01 TO 8MHz
VR01811
相關PDF資料
PDF描述
ST6228CN3 CB 5C 5#16S PIN RECP WALL
ST6228CN6 ER 5C 5#16S PIN RECP WALL
ST6391 8-BIT HCMOS MCUs FOR TV FREQUENCY SYNTHESIS WITH OSD
ST6392B1 8-BIT HCMOS MCUs FOR TV FREQUENCY SYNTHESIS WITH OSD
ST6393B1 8-BIT HCMOS MCUs FOR TV FREQUENCY SYNTHESIS WITH OSD
相關代理商/技術參數
參數描述
ST6228CN1/XXX 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-Bit Microcontroller
ST6228CN3 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:8-BIT MCUs WITH A/D CONVERTER, AUTO-RELOAD TIMER, UART, OSG, SAFE RESET AND 28-PIN PACKAGE
ST6228CN3/XXX 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-Bit Microcontroller
ST6228CN6 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:8-BIT MCUs WITH A/D CONVERTER, AUTO-RELOAD TIMER, UART, OSG, SAFE RESET AND 28-PIN PACKAGE
ST6228CN6/XXX 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-Bit Microcontroller