參數資料
型號: T7121
英文描述: T7121 HDLC Interface for ISDN
中文描述: T7121的HDLC接口用于ISDN
文件頁數: 19/68頁
文件大?。?/td> 685K
代理商: T7121
Lucent Technologies Inc.
19
Data Sheet
April 1997
T7121 HDLC Interface for ISDN (HIFI-64)
Functional Description
(continued)
SLD and IOM2 Examples
Example register settings for configuring to SLD, IOM2, or K2 TDM highways are shown below. These settings
assume HWYEN (R0—B7) = 1 and FSPOL (R0—B6) = 1.
HDLC Operation
This section describes the standard HDLC functions performed by the HIFI-64. HDLC operation is the default
mode of operation. The transmitter accepts parallel data from the transmit FIFO, converts it to a serial bit stream,
provides bit stuffing as necessary, adds the CRC and the opening and closing flags, and sends the framed serial
bit stream on the selected transmit data pin(s). The receiver accepts serial data on the selected receive data pin,
identifies frames for proper format, reconstructs data bytes, provides bit destuffing as necessary, and loads parallel
data in the receive FIFO. HDLC frames on the serial link have the following format:
All bits between the opening flag and the CRC are considered user data bits. User data bits such as the address,
control, and information fields for LAPB or LAPD frames are fetched from the transmit FIFO for transmission.
Received user data bits are stored in the FIFO buffers. The 16 bits preceding the closing flag are the frame check
sequence or cyclic redundancy check (CRC) bits.
Zero-Bit Insertion/Deletion (Bit Stuffing/Destuffing)
The HDLC protocol recognizes three special bit patterns: flags, aborts, and idles. These patterns have the com-
mon characteristic of containing at least six consecutive 1s. A user data byte can contain one of these special pat-
terns. Transmitter zero-bit stuffing is done on user data and CRC fields of the frame to avoid transmitting one of
these special patterns. Whenever five 1s occur between flags, a 0 bit is automatically inserted after the fifth 1, prior
to transmission of the next bit. On the receive side, if five successive 1s are detected followed by a 0, the 0 is
assumed to have been inserted and is deleted (bit destuffing).
Table 4. Example Register Settings
Register
IOM2/GCI
0
1
1
1
111
(# of time slots) – 1
Desired time slot
0
111
(# of time slots) – 1
Desired time slot
SLD
0
1
0
1
111
000011
K2
0
1
0
1
111
FE, (R0—B5)
P21CTL, (R5—B6)
CMS, (R8—B6)
CLKXI, (R9—B4)
TBOF[2—0], (R9—B[7—5])
TTSOF[5 0], (R10—B[5—0])
TSLT[5—0], (R7—B[5—0])
CLKRI, (R9—B0)
RBOF[2—0], (R9—B[3—1])
RTSOF[5—0], (R11—B[5—0])
RSLT[5—0], (R8—B[5—0])
000000, 000111
000001—000111, 000000
0
111
000000, 000111
000001—000111, 000000
000000—000011
0
111
000011
000100—000111
Opening Flag
01111110
User Data Field
8 bits
Frame Check Sequence (CRC)
16 bits
Closing Flag
01111110
相關PDF資料
PDF描述
T7121-EL2 T7121 HDLC Interface for ISDN
T7121-PL2 T7121 HDLC Interface for ISDN
T7121 HDLC Interface for ISDN (HIFI-64)(應用于ISDN的HDLC(高階數據鏈路)接口)
T7502 T7502 Dual PCM Codec with Filters
T7503 T7503 Dual PCM Codec with Filters
相關代理商/技術參數
參數描述
T7-121A1 制造商:OTTO 功能描述:Toggle Switches ON NONE OFF 1 Pole Standard Bat Handle 制造商:OTTO Engineering Inc 功能描述:Switch Toggle ON None OFF SPST Bat Toggle Screw 16A 115VAC 28VDC Panel Mount with Threads
T7-121A2D 制造商:OTTO 功能描述:Toggle Switches ON NONE OFF 1 Pole Standard LeverLock 制造商:OTTO Engineering Inc 功能描述:1 POLE, SCREW, STD,
T7-121A2G 功能描述:撥動開關 ON NONE OFF 1 Pole Standard LeverLock RoHS:否 制造商:OTTO 觸點形式: 開關功能: 電流額定值: 電壓額定值 AC: 電壓額定值 DC: 功率額定值: 端接類型: 安裝風格: 端子密封: 觸點電鍍: 照明:
T7-121A5 制造商:OTTO 功能描述:Toggle Switches ON NONE OFF 1 Pole Standard Bat Handle 制造商:OTTO Engineering Inc 功能描述:Switch Toggle ON None OFF SPST Bat Toggle Screw 16A 115VAC 28VDC Panel Mount with Threads
T7-121B1 功能描述:撥動開關 ON NONE ON 1 Pole Standard Bat Handle RoHS:否 制造商:OTTO 觸點形式: 開關功能: 電流額定值: 電壓額定值 AC: 電壓額定值 DC: 功率額定值: 端接類型: 安裝風格: 端子密封: 觸點電鍍: 照明: