- 您現在的位置：買賣IC網 > PDF目錄371180 > T8531 T8502 and T8503 Dual PCM Codecs with Filters PDF資料下載
參數資料
| 型號： | T8531 |
| 元件分類： | Codec |
| 英文描述： | T8502 and T8503 Dual PCM Codecs with Filters |
| 中文描述： | T8502和T8503雙的PCM編解碼器與濾波器 |
| 文件頁數： | 22/48頁 |
| 文件大?。?/td> | 999K |
| 代理商： | T8531 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁當前第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁
22
Lucent Technologies Inc.
Preliminary Data Sheet
November 2000
Codec Chip Set
T8531/T8532 Multichannel Programmable
Chip Set Functional Description
(continued)
Start-Up After Internal Reset
(continued)
Autocalibration
Autocalibration is an analog self-test and trimming pro-
cedure controlled by the DSP core. Sine wave signals
are generated in the receive direction. These signals
are looped back at the analog side of the T8532, and
the return signal amplitudes are measured in the trans-
mit path. This procedure provides on-the-spot fault
coverage of the transmit and receive paths. It also cali-
brates the octal devices by modifying the gain on each
channel. Channel four of the T8532 is the only channel
trimmed at the factory for absolute gain accuracy.
When autocalibration is run, all channels are trimmed
with reference to channel four. That is, the gain on
each channel is adjusted so that its absolute gain is
equivalent to that of the trimmed channel. Performing
trimming in this manner provides channel-to-channel
gain matching of better than 0.01 dB. This is a much
better performance than could be achieved using con-
ventional trimming. Trimmed values are placed in data
storage, and absolute gain values are then modified
accordingly any time the absolute gain register is
changed.
The calibration sequence measures the looped-back
power result and compares it to the calibrated channel.
The trim window is
±
0.2 dB. If any channel exhibits a
power value which is greater than
±
0.2 dB, the calibra-
tion procedure sets a failure flag for that channel. Trim-
ming will not be performed on the failed channel, and
the channel’s trimmed gain will be left at 0 dB. The
failed channel, therefore, is left in its previous state and
can still be used. The results of calibration are held in
RAM address 0x07F4 for transmit (pass 1) and 0x07F5
for receive (pass 2). A bit is set high for every failed
channel.
The preceding section discussed the sequence of
instructions that must be followed in order to properly
configure the T8531 for normal operation. The auto-
calibration procedure is mandatory after hardware
reset.
Tone Plant
The following tone plant functions are provided in ROM
code in the T8531 device.
DTMF Transceiver
DTMF generation and detection satisfies LSSGR Sig-
naling for Analog Interfaces GR-506 CORE, section
15.
Caller Line Identification
Called ID transmission is performed as specified in TR-
NWT-000031 (CLASS feature: calling number deliv-
ery).
Call Progress Tones
A call progress tone generator is provided. This tone
generator complies with
Telcordia
* GR-506-CORE
requirements.
* Telcordiais a trademark of Bell Communications Research, Inc.
相關PDF資料 |
PDF描述 |
|---|---|
| T8532 | T8502 and T8503 Dual PCM Codecs with Filters |
| T8533 | T8533/34 Quad Programmable Line Card Signal Processor |
| T8534 | T8533/34 Quad Programmable Line Card Signal Processor |
| T8535B | T8535B/T8536B Quad Programmable Codec |
| T8536B | T8535B/T8536B Quad Programmable Codec |
相關代理商/技術參數 |
參數描述 |
|---|---|
| T8531A | 制造商:AGERE 制造商全稱:AGERE 功能描述:T8531A/8532 Multichannel Programmable Codec Chip Set |
| T8532 | 制造商:AGERE 制造商全稱:AGERE 功能描述:T8531A/8532 Multichannel Programmable Codec Chip Set |
| T8533 | 制造商:AGERE 制造商全稱:AGERE 功能描述:T8533/34 Quad Programmable Line Card Signal Processor |
| T85331G | 制造商:BITECH 制造商全稱:Bi technologies 功能描述:Thick Film Super Low Profile SIP Resistor Networks |
| T85331J | 制造商:BITECH 制造商全稱:Bi technologies 功能描述:Thick Film Super Low Profile SIP Resistor Networks |
發布緊急采購，3分鐘左右您將得到回復。