參數資料
型號： TDA8752BH
廠商： NXP Semiconductors N.V.
英文描述： Triple high-speed Analog-to-Digital Converter 110 Msps ADC
中文描述： 三高速模擬數字轉換器110 MSPS的ADC的
文件頁數： 12/36頁
文件大小： 154K
代理商： TDA8752BH
2000 Jan 10
12
Philips Semiconductors
Preliminary specification
Triple high-speed Analog-to-Digital
Converter 110 Msps (ADC)
TDA8752B
ADC outputs
ADC outputs are straight binary. An output enable pin
(OE; active LOW) enables the output status between
active and high-impedance (OE = HIGH) to be switched;
it is recommended to load the outputs with a 10 pF
capacitive load. The timing must be checked very carefully
if the capacitive load is more than 10 pF.
Phase-locked loop
The ADCs are clocked either by an internal PLL locked to
the CKREF clock, (all of the PLL is on-chip except the loop
filter capacitance) or an external clock, CKEXT. Selection
is performed via the serial interface bus.
The reference clock (CKREF) range is between
15 and 280 kHz. Consequently, the VCO minimum
frequency is 12 MHz and the maximum frequency
110 MHz for the TDA8752B/8. The gain of the VCO part
can be controlled via the serial interface, depending on the
frequency range to which the PLL is locked.
To increase the bandwidth of the PLL, the charge pump
current, controlled by the serial interface, must also be
increased. The relationship between the frequency and
the current is given by the following equation:
Where:
f
n
= the natural PLL frequency
K
O
= the VCO gain
D
R
= PLL divider ratio
C
z
and C
P
= capacitors of the PLL filter.
The other PLL equation is as follows:
Where:
f
z
= loop filter zero frequency
R = the chosen resistance for the filter
ξ
= the damping factor.
F
O
= 0 dB loop gain frequency
Different resistances for the filter can be programmed via
the serial interface. To improve the performances, the PLL
parameters should be chosen so that:
The values of R and I
p
must be chosen so that the product
is the closest to Lim. In the event that there are several
choices, the couple for which the
ξ
value is the closest to 1
must be chosen.
A software call “PLL calculator’” is available on Philips
Semiconductor Internet site to calculate the best PLL
parameters.
It is possible to control (independently) the phase of the
ADC clock and the phase of an additional clock output
(which could be used to drive a second TDA8752B). For
this, two serial interface-controlled digital phase-shift
controllers are included (controlled by 5-bit registers,
phase shift controller steps are 11.25
°
each on the whole
PLL frequency range).
CKREF is resynchronized, by the synchro block, on the
CKAO clock. The output is CKREFO (LOW during 8 clock
periods). CKAO is the clock at the output of the phase
selector A. This clock can be used as the clocks for CKBO
and CKADCO. The timing is given in Fig.5.
The COAST pin is used to disconnect the PLL phase
frequency detector during the frame flyback or the
unavailability of the CKREF signal. This signal can
normally be derived from the VSYNC signal.
fn
2
π
--1
KOIP
DRCz
CP
)
+
-------------------------------------
=
fz
R
π
×
Cz
×
2
ξ
1
2
fn
fz
----
×
=
=
FO
ξ
fn
R IP
=
2
π
DRFO
----------KO
=
ref
f
0.15
R IP
0 3
π
-------------KO
Lim
=
≤
≤
相關PDF資料
PDF描述
TDA8753 YUV 8-bit analog-to-digital interface
TDA8753A YUV 8-bit analog-to-digital interface
TDA8758 YC8-bit Video Low-Power Analog-to-Digital Interface(YC8位視頻低功耗模數接口)
TDA8758G YC 8-bit low-power analog-to-digital video interface
TDA8763AM 10-bit high-speed low-power ADC
相關代理商/技術參數
參數描述
TDA8752BH/8 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Triple high-speed Analog-to-Digital Converter 110 Msps ADC
TDA8752H 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Triple high speed Analog-to-Digital Converter ADC
TDA8752H/6 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Triple high speed Analog-to-Digital Converter ADC
TDA8752H/8 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Triple high speed Analog-to-Digital Converter ADC
TDA8753 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:YUV 8-bit analog-to-digital interface
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*