參數資料
型號: TPS2459RHB
廠商: TEXAS INSTRUMENTS INC
元件分類: 電源管理
英文描述: 2-CHANNEL POWER SUPPLY SUPPORT CKT, PQCC32
封裝: PLASTIC, QFN-32
文件頁數: 28/48頁
文件大小: 852K
代理商: TPS2459RHB
FAULT
IN12
CL
P
0.01
V
I
@
SLUS917D – FEBRUARY 2009 – REVISED MAY 2010
www.ti.com
Fault Timer Programming
Both of the TPS2459 channels include a fault timer. The timer begins operating whenever the channel enters
current limit. If the channel remains in current limit so long that the fault timer runs out, then the channel turns off
the pass FET and reports a fault condition by means of the xFLT bit in the I2C interface.
The fault timers are independently programmable from 0.5 to 15.5 ms in steps of 0.5 ms using the appropriate
xFT bits. A code of xFT = 00001B corresponds to the minimum programmable time of 0.5 ms. The code xFT =
00000B corresponds to an extremely short time interval of no practical use. The locations of the fault timer
programming bits are shown in Table 13.
Table 13. Fault Time Control Bits
FAULT TIME (ms)
CHANNEL
VOLTAGE (V)
8
4
2
1
0.5
12
R4[4]
R4[3]
R4[2]
R4[1]
R4[0]
REGISTER[
BIT]
3.3
R5[4]
R5[3]
R5[2]
R5[1]
R5[0]
Select the shortest fault times sufficient to allow down-stream loads and bulk capacitors to charge. Shorter fault
times reduce the stresses imposed on the pass FETs under fault conditions. This consideration may allow the
use of smaller and less expensive pass FETs for the 12-V channels.
The TPS2459 supports two modes of fault timer operation. Clearing the FLTMODE bit causes a channel to latch
off whenever its fault timer runs out. The channel remains off until it has been disabled and re-enabled (see
Enable Functions section). The TPS2459 operates in this manner by default. Setting the FLTMODE bit causes a
faulted channel to automatically attempt to turn back on after a delay roughly one hundred times the fault time.
This process repeats until either the fault disappears or the user disables the channel. The pass FET for a 12-V
channel with a shorted output must therefore continuously dissipate the following power;
where
VIN12 equals the voltage present at the input of the 12-V channel
ICL equals the current limit setting for this channel (the inrush current if 12VNRS is set)
(15)
When used in MicroTCA Power Modules it is very important to protect the OUT12 pin by connecting a Schottky
diode from the OUT12 pin to GND. The relatively long and uncontrolled load line lengths to the AdvancedMC
modules make it quite likely that shutting off while under load causes an inductive transient to pull the OUT12 pin
below -0.3 V. Pulling OUT12 below this level can disrupt proper device operation.
34
Copyright 2009–2010, Texas Instruments Incorporated
Product Folder Link(s): TPS2459
相關PDF資料
PDF描述
TPS24701DGK POWER SUPPLY SUPPORT CKT, PDSO8
TPS24710DGS POWER SUPPLY SUPPORT CKT, PDSO10
TPS24710 POWER SUPPLY SUPPORT CKT, PDSO10
TPS24711 POWER SUPPLY SUPPORT CKT, PDSO10
TPS24711DGSR POWER SUPPLY SUPPORT CKT, PDSO10
相關代理商/技術參數
參數描述
TPS2459RHBR 功能描述:熱插拔功率分布 3V/12V Hot Swap & ORing Controller RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube
TPS2459RHBT 功能描述:熱插拔功率分布 3V/12V Hot Swap & ORing Controller RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube
TPS2459RHBT 制造商:Texas Instruments 功能描述:Hot Swap Controllers TI 制造商:Texas Instruments 功能描述:IC, HOT SWAP & O-RING CTRL, 23V, QFN-32
TPS24700DGK 功能描述:熱插拔功率分布 2.5-18V Hi Eff Hot- Swap Controller RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube
TPS24700DGKR 功能描述:熱插拔功率分布 2.5-18V Hi Eff Hot- Swap Controller RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube