參數資料
型號： TSC2302IRGZR
元件分類： Codec
英文描述： PROGRAMMABLE TOUCH SCREEN CONTROLLER WITH STEREO AUDIO CODEC
中文描述： 可編程觸摸屏控制器，立體聲編解碼器
文件頁數： 33/81頁
文件大小： 1211K
代理商： TSC2302IRGZR
www.ti.com
www.ti.com
tcoordinate
2.5 s
2 tPVS
tPRE
tSNS
2NAVGNBITS
1
fconv
4.4 s
(4)
tcoordinate
4.75 s
3 tPVS
tPRE
tSNS
4NAVGNBITS
1
fconv
4.4 s
(5)
TSC2302
SLAS394–JULY 2003
OPERATION - TOUCH SCREEN MEASUREMENTS
Conversion Controlled by TSC2302 Initiated at Touch Detect
In this mode, the TSC2302 detects when the touch panel is touched and causes the PENIRQ line to go low. At
the same time, the TSC2302 powers up its internal clock. It then turns on the Y-drivers, and after a programmed
panel voltage stabilization time, powers up the ADC and convert the Y coordinate. If averaging is selected,
several conversions may take place; when data averaging is complete, the Y coordinate result is stored in the Y
register.
This mode is recommended to fully utilize the integrated touch screen processing of the TSC2302 and reduce
the processing overhead and number of interrupts to the host processor. In this mode, the host processor does
not need to monitor PENIRQ, instead the host needs only to configure the TSC2302 once at power-up, and then
monitor DAV and read back data after a falling edge on DAV.
If the screen is still touched at this time, the X-drivers are enabled, and the process repeats, but measures
instead the X coordinate, storing the result in the X register.
If only X and Y coordinates are to be measured, then the conversion process is complete. Figure 46 shows a
flowchart for this process. The time it takes to go through this process depends upon the selected resolution,
internal conversion clock rate, averaging selected, panel voltage stabilization time, and precharge and sense
times.
The time needed to get a complete X/Y coordinate reading can be calculated by:
where:
t
coordinate
= time to complete X/Y coordinate reading;
t
PVS
= panel voltage stabilization time, as given in Table 10;
t
PRE
= precharge time, as given in Table 17;
t
SNS
= sense time, as given in Table 18;
N
AVG
= number of averages, as given in Table 8; for no averaging, NAVG = 1;
N
BITS
= number of bits of resolution, as given in Table 7;
f
conv
= A/D converter clock frequency, as given in Table 9.
If the pressure of the touch is also to be measured, the process continues after the X-conversion is complete,
measuring the Z1 and Z2 values, and placing them in the Z1 and Z2 registers. This process is illustrated in
Figure 47. As before, this process time depends upon the settings described above. The time for a complete
X/Y/Z1/Z2 coordinate reading is given by:
33
相關PDF資料
PDF描述
TSC87C51 CMOS 0 to 25 MHz Programmable 8?bit Microcontroller
TSC87C51-25MGMQ CMOS 0 to 25 MHz Programmable 8?bit Microcontroller
TSC87C51-25MIMQ CMOS 0 to 25 MHz Programmable 8?bit Microcontroller
TSC87C51-25MJMQ CMOS 0 to 25 MHz Programmable 8?bit Microcontroller
TSM600-250-RA PolySwitch PTC Devices Overcurrent Protection Device
相關代理商/技術參數
參數描述
TSC2302IRGZRG4 功能描述:觸摸屏轉換器和控制器 Prog 4-Wire w/20-Bit Stereo Audio Codec RoHS:否 制造商:Microchip Technology 類型:Resistive Touch Controllers 輸入類型:3 Key 數據速率:140 SPS 分辨率:10 bit 接口類型:4-Wire, 5-Wire, 8-Wire, I2C, SPI 電源電壓:2.5 V to 5.25 V 電源電流:17 mA 工作溫度:- 40 C to + 85 C 封裝 / 箱體:SSOP-20
TSC2303IZQZ 制造商:Texas Instruments 功能描述:
TSC2303IZQZR 制造商:Texas Instruments 功能描述:
TSC236 制造商:TSC 制造商全稱:Taiwan Semiconductor Company, Ltd 功能描述:High Voltage NPN Transistor
TSC236CIC0 制造商:TSC 制造商全稱:Taiwan Semiconductor Company, Ltd 功能描述:High Voltage NPN Transistor
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*