參數資料
型號: TSC2302IRGZR
元件分類: Codec
英文描述: PROGRAMMABLE TOUCH SCREEN CONTROLLER WITH STEREO AUDIO CODEC
中文描述: 可編程觸摸屏控制器,立體聲編解碼器
文件頁數: 78/81頁
文件大?。?/td> 1211K
代理商: TSC2302IRGZR
www.ti.com
TSC2302
SLAS394–JULY 2003
With this in mind, power to the TSC2302 must be clean and well bypassed. A 0.1-μF ceramic bypass capacitor
should be placed as close to the device as possible on each supply pin to its respective ground pin. A 1-μF to
10-μF capacitor may also be needed if the impedance of the connection between a supply and the power supply
is high.
A bypass capacitor on the SAR VREF pin may not be absolutely necessary because this reference is buffered by
an internal op amp, but a 0.1uF bypass capacitor may reduce noise on this reference. If an external reference
voltage originates from an op amp, make sure that it can drive any bypass capacitor that is used without
oscillation.
The TSC2302 SAR converter architecture offers no inherent rejection of noise or voltage variation in regards to
using an external reference input. This is of particular concern when the reference input is tied to the power
supply. Any noise and ripple from the supply appears directly in the digital results. While high frequency noise
can be filtered out, voltage variation due to line frequency (50 Hz or 60 Hz) can be difficult to remove.
The HPGND pin must be connected to a clean ground point. In many cases, this is the analog ground for the
SAR converter. Avoid connections which are too near the grounding point of a microcontroller or digital signal
processor. If needed, run a ground trace directly from the converter to the power supply entry or battery
connection point. The ideal layout includes an analog ground plane dedicated to the converter and associated
analog circuitry.
In the specific case of use with a resistive touch screen, care must be taken with the connection between the
converter and the touch screen. Since resistive touch screens have fairly low resistance, the interconnection
should be as short and robust as possible. Loose connections can be a source of error when the contact
resistance changes with flexing or vibrations.
As indicated previously, noise can be a major source of error in touch screen applications (e.g., applications that
require a back-lit LCD panel). This EMI noise can be coupled through the LCD panel to the touch screen and
cause
flickering
of the converted data. Several things can be done to reduce this error, such as utilizing a touch
screen with a bottom-side metal layer connected to ground. This couples the majority of noise to ground.
Additionally, filtering capacitors, from Y+, Y-, X+, and X- to ground, can also help. Note, however, that the use of
these capacitors increases screen settling time and requires longer panel voltage stabilization times, as well as
increased precharge and sense times for the touch screen control circuitry of the TSC2302.
78
相關PDF資料
PDF描述
TSC87C51 CMOS 0 to 25 MHz Programmable 8?bit Microcontroller
TSC87C51-25MGMQ CMOS 0 to 25 MHz Programmable 8?bit Microcontroller
TSC87C51-25MIMQ CMOS 0 to 25 MHz Programmable 8?bit Microcontroller
TSC87C51-25MJMQ CMOS 0 to 25 MHz Programmable 8?bit Microcontroller
TSM600-250-RA PolySwitch PTC Devices Overcurrent Protection Device
相關代理商/技術參數
參數描述
TSC2302IRGZRG4 功能描述:觸摸屏轉換器和控制器 Prog 4-Wire w/20-Bit Stereo Audio Codec RoHS:否 制造商:Microchip Technology 類型:Resistive Touch Controllers 輸入類型:3 Key 數據速率:140 SPS 分辨率:10 bit 接口類型:4-Wire, 5-Wire, 8-Wire, I2C, SPI 電源電壓:2.5 V to 5.25 V 電源電流:17 mA 工作溫度:- 40 C to + 85 C 封裝 / 箱體:SSOP-20
TSC2303IZQZ 制造商:Texas Instruments 功能描述:
TSC2303IZQZR 制造商:Texas Instruments 功能描述:
TSC236 制造商:TSC 制造商全稱:Taiwan Semiconductor Company, Ltd 功能描述:High Voltage NPN Transistor
TSC236CIC0 制造商:TSC 制造商全稱:Taiwan Semiconductor Company, Ltd 功能描述:High Voltage NPN Transistor