- 您現在的位置：買賣IC網 > PDF目錄225499 > V58C365164S5 (MOSEL-VITELIC) 4M X 16 DDR DRAM, 0.1 ns, PDSO66 PDF資料下載
參數資料
| 型號： | V58C365164S5 |
| 廠商： | MOSEL-VITELIC |
| 元件分類： | DRAM |
| 英文描述： | 4M X 16 DDR DRAM, 0.1 ns, PDSO66 |
| 封裝： | 0.400 INCH, PLASTIC, TSOP2-66 |
| 文件頁數： | 11/44頁 |
| 文件大小： | 507K |
| 代理商： | V58C365164S5 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁當前第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁
19
V58C365164S Rev. 1.5 November 2001
MOSEL VITELIC
V58C365164S
Precharge Timing During Write Operation
Precharge timing for Write operations in DRAMs requires enough time to satisfy the write recovery require-
ment. This is the time required by a DRAM sense amp to fully store the voltage level. For DDR SDRAMs, a
timing parameter (t
WR) is used to indicate the required amount of time between the last valid write operation
and a Precharge command to the same bank.
The “write recovery” operation begins on the rising clock edge after the last DQS edge that is used to strobe
in the last valid write data. “Write recovery” is complete on the next rising clock edge that is used to strobe in
the Precharge command.
For the earliest possible Precharge command following a Write burst without interrupting the burst, the
minimum time for “write recovery” is 1.25 clock cycles. Maximum “write recovery” time is 1.75 clock cycles.
Write with Precharge Timing
(CAS Latency = Any; Burst Length = 4)
T0
T1
T2
T3
T4
T5
T6
T7
T8
D0
D1
D2
D3
NOP
Write
NOP
PreA
NOP
CK, CK
Command
DQS
DQ
tRAS(min)
tRP(min)
BA
NOP
T9
T10
tWR(min)
D0
D1
D2
D3
DQS
DQ
tWR(max)
BA
相關PDF資料 |
PDF描述 |
|---|---|
| V608ME06 | VCO, 1900 MHz - 2270 MHz |
| V603ME07 | VCO, 1896 MHz - 1924 MHz |
| V6049001 | VCO, 1600 MHz - 2200 MHz |
| V610ME04 | VCO, 1950 MHz - 2150 MHz |
| V62/04634-01 | SPECIALTY ANALOG CIRCUIT, PDSO14 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| V590ME01 | 制造商:ZCOMM 制造商全稱:ZCOMM 功能描述:LOW COST - HIGH PERFORMANCE VOLTAGE CONTROLLED OSCILLATOR |
| V590ME01-LF | 制造商:ZCOMM 制造商全稱:ZCOMM 功能描述:Voltage-Controlled Oscillator Surface Mount Module |
| V590ME01-LF_10 | 制造商:ZCOMM 制造商全稱:ZCOMM 功能描述:Voltage-Controlled Oscillator Surface Mount Module |
| V590ME08 | 制造商:ZCOMM 制造商全稱:ZCOMM 功能描述:VOLTAGE CONTROLLED OSCILLATOR |
| V590ME08-LF | 制造商:ZCOMM 制造商全稱:ZCOMM 功能描述:Voltage-Controlled Oscillator Surface Mount Module |
發布緊急采購，3分鐘左右您將得到回復。