參數資料
型號： V58C365164S5
廠商： MOSEL-VITELIC
元件分類： DRAM
英文描述： 4M X 16 DDR DRAM, 0.1 ns, PDSO66
封裝： 0.400 INCH, PLASTIC, TSOP2-66
文件頁數： 14/44頁
文件大?。?/td> 507K
代理商： V58C365164S5
21
V58C365164S Rev. 1.5 November 2001
MOSEL VITELIC
V58C365164S
Read Interrupted by a Write
To interrupt a Burst Read with a Write command, a Burst Stop command must be asserted to stop the burst
read operation and 3-state the DQ bus. Additionally, control of the DQS bus must be turned around to allow
the memory controller to drive the data strobe signal (DQS) into the DDR SDRAM for the write cycles. Once
the Burst Stop command has been issued, a Write command can not be issued until a minimum delay or
latency (L
BST) has been satisfied. This latency is measured from the Burst Stop command and is equivalent
to the CAS latency programmed into the mode register. In instances where CAS latency is measured in half
clock cycles, the minimum delay (L
BST) is rounded up to the next full clock cycle (i.e., if CL=2 then LBST=2, if
CL=2.5 then L
BST=3). It is illegal to interrupt a Read with autoprecharge command with a Write command.
Read Interrupted by Burst Stop Command Followed by a Write Command Timing
Write Interrupted by a Write
A Burst Write can be interrupted before completion by a new Write command to any bank. When the pre-
vious burst is interrupted, the remaining addresses are overridden with a full burst length starting with the new
address. The data from the first Write command continues to be input into the device until the Write Latency
of the interrupting Write command is satisfied (WL=1) At this point, the data from the interrupting Write com-
mand is input into the device. Write commands can be issued on each rising edge of the system clock. It is
illegal to interrupt a Write with autoprecharge command with a Write command.
Write Interrupted by a Write Command Timing
(CAS Latency = 2; Burst Length = 4)
T0
T1
T2
T3
T4
T5
T6
T7
T8
BST
NOP
Write
NOP
D0
D1
Read
D0
D1
D2
D3
CK, CK
Command
DQS
DQ
T9
LBST
(CAS Latency = Any; Burst Length = 4)
T0
T1
T2
T3
T4
T5
T6
T7
T8
WriteA
NOP
WriteB
NOP
DA0 DA1 DB0 DB1 DB2 DB3
CK, CK
Command
DQS
DQ
DM
T9
Write Latency
DM0 DM1 DM0 DM1 DM2 DM3
相關PDF資料
PDF描述
V608ME06 VCO, 1900 MHz - 2270 MHz
V603ME07 VCO, 1896 MHz - 1924 MHz
V6049001 VCO, 1600 MHz - 2200 MHz
V610ME04 VCO, 1950 MHz - 2150 MHz
V62/04634-01 SPECIALTY ANALOG CIRCUIT, PDSO14
相關代理商/技術參數
參數描述
V590ME01 制造商:ZCOMM 制造商全稱:ZCOMM 功能描述:LOW COST - HIGH PERFORMANCE VOLTAGE CONTROLLED OSCILLATOR
V590ME01-LF 制造商:ZCOMM 制造商全稱:ZCOMM 功能描述:Voltage-Controlled Oscillator Surface Mount Module
V590ME01-LF_10 制造商:ZCOMM 制造商全稱:ZCOMM 功能描述:Voltage-Controlled Oscillator Surface Mount Module
V590ME08 制造商:ZCOMM 制造商全稱:ZCOMM 功能描述:VOLTAGE CONTROLLED OSCILLATOR
V590ME08-LF 制造商:ZCOMM 制造商全稱:ZCOMM 功能描述:Voltage-Controlled Oscillator Surface Mount Module
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*