- 您現在的位置：買賣IC網 > PDF目錄225499 > V58C365164S5 (MOSEL-VITELIC) 4M X 16 DDR DRAM, 0.1 ns, PDSO66 PDF資料下載
參數資料
| 型號： | V58C365164S5 |
| 廠商： | MOSEL-VITELIC |
| 元件分類： | DRAM |
| 英文描述： | 4M X 16 DDR DRAM, 0.1 ns, PDSO66 |
| 封裝： | 0.400 INCH, PLASTIC, TSOP2-66 |
| 文件頁數： | 43/44頁 |
| 文件大?。?/td> | 507K |
| 代理商： | V58C365164S5 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁當前第43頁第44頁
8
V58C365164S Rev. 1.5 November 2001
MOSEL VITELIC
V58C365164S
Bank Activate Command
The Bank Activate command is issued by holding CAS and WE high with CS and RAS low at the rising
edge of the clock. The DDR SDRAM has four independent banks, so two Bank Select addresses (BA0 and
BA1) are supported. The Bank Activate command must be applied before any Read or Write operation can
be executed. The delay from the Bank Activate command to the first Read or Write command must meet or
exceed the minimum RAS to CAS delay time (tRCD min). Once a bank has been activated, it must be pre-
charged before another Bank Activate command can be applied to the same bank. The minimum time interval
between interleaved Bank Activate commands (Bank A to Bank B and vice versa) is the Bank to Bank delay
time (tRRD min).
Bank Activation Timing
Read Operation
With the DLL enabled, all devices operating at the same frequency within a system are ensured to have
the same timing relationship between DQ and DQS relative to the CK input regardless of device density, pro-
cess variation, or technology generation.
The data strobe signal (DQS) is driven off chip simultaneously with the output data (DQ) during each read
cycle. The same internal clock phase is used to drive both the output data and data strobe signal off chip to
minimize skew between data strobe and output data. This internal clock phase is nominally aligned to the
input differential clock (CK, CK) by the on-chip DLL. Therefore, when the DLL is enabled and the clock fre-
quency is within the specified range for proper DLL operation, the data strobe (DQS), output data (DQ), and
the system clock (CK) are all nominally aligned.
Since the data strobe and output data are tightly coupled in the system, the data strobe signal may be delayed
and used to latch the output data into the receiving device. The tolerance for skew between DQS and DQ
(t
DQSQ) is tighter than that possible for CK to DQ (tAC)orDQS to CK (tDQSCK).
T0
T1
T2
T3
Tn
Tn+1
Tn+2
Tn+3
Tn+4
Tn+5
(CAS Latency = 2; Burst Length = Any)
tRRD(min)
tRP(min)
tRC
tRCD(min)
Begin Precharge Bank A
CK, CK
BA/Address
Command
Bank/Col
Read/A
Bank/Row
Activate/A
Activate/B
Pre/A
Bank/Row
Activate/A
Bank
Bank/Row
tRAS(min)
相關PDF資料 |
PDF描述 |
|---|---|
| V608ME06 | VCO, 1900 MHz - 2270 MHz |
| V603ME07 | VCO, 1896 MHz - 1924 MHz |
| V6049001 | VCO, 1600 MHz - 2200 MHz |
| V610ME04 | VCO, 1950 MHz - 2150 MHz |
| V62/04634-01 | SPECIALTY ANALOG CIRCUIT, PDSO14 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| V590ME01 | 制造商:ZCOMM 制造商全稱:ZCOMM 功能描述:LOW COST - HIGH PERFORMANCE VOLTAGE CONTROLLED OSCILLATOR |
| V590ME01-LF | 制造商:ZCOMM 制造商全稱:ZCOMM 功能描述:Voltage-Controlled Oscillator Surface Mount Module |
| V590ME01-LF_10 | 制造商:ZCOMM 制造商全稱:ZCOMM 功能描述:Voltage-Controlled Oscillator Surface Mount Module |
| V590ME08 | 制造商:ZCOMM 制造商全稱:ZCOMM 功能描述:VOLTAGE CONTROLLED OSCILLATOR |
| V590ME08-LF | 制造商:ZCOMM 制造商全稱:ZCOMM 功能描述:Voltage-Controlled Oscillator Surface Mount Module |
發布緊急采購，3分鐘左右您將得到回復。