- 您現在的位置：買賣IC網 > PDF目錄245689 > W25Q16DWSFIG (WINBOND ELECTRONICS CORP) 16M X 1 SPI BUS SERIAL EEPROM, PDSO16 PDF資料下載
參數資料
| 型號： | W25Q16DWSFIG |
| 廠商： | WINBOND ELECTRONICS CORP |
| 元件分類： | PROM |
| 英文描述： | 16M X 1 SPI BUS SERIAL EEPROM, PDSO16 |
| 封裝： | 0.300 INCH, GREEN, PLASTIC, SOIC-16 |
| 文件頁數： | 10/83頁 |
| 文件大?。?/td> | 1268K |
| 代理商： | W25Q16DWSFIG |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁當前第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁
W25Q16DW
- 18 -
10.2 INSTRUCTIONS
The Standard/Dual/Quad SPI instruction set of the W25Q16DW consists of thirty six basic instructions
that are fully controlled through the SPI bus (see Instruction Set table1-3). Instructions are initiated with
the falling edge of Chip Select (/CS). The first byte of data clocked into the DI input provides the
instruction code. Data on the DI input is sampled on the rising edge of clock with most significant bit
(MSB) first.
The QPI instruction set of the W25Q16DW consists of twenty four basic instructions that are fully
controlled through the SPI bus (see Instruction Set table 4). Instructions are initiated with the falling edge
of Chip Select (/CS). The first byte of data clocked through IO[3:0] pins provides the instruction code. Data
on all four IO pins are sampled on the rising edge of clock with most significant bit (MSB) first. All QPI
instructions, addresses, data and dummy bytes are using all four IO pins to transfer every byte of data with
every two serial clocks (CLK).
Instructions vary in length from a single byte to several bytes and may be followed by address bytes, data
bytes, dummy bytes (don’t care), and in some cases, a combination. Instructions are completed with the
rising edge of edge /CS. Clock relative timing diagrams for each instruction are included in figures 5
through 42. All read instructions can be completed after any clocked bit. However, all instructions that
Write, Program or Erase must complete on a byte boundary (/CS driven high after a full 8-bits have been
clocked) otherwise the instruction will be ignored. This feature further protects the device from inadvertent
writes. Additionally, while the memory is being programmed or erased, or when the Status Register is
being written, all instructions except for Read Status Register will be ignored until the program or erase
cycle has completed.
10.2.1 Manufacturer and Device Identification
MANUFACTURER ID
(MF7 - MF0)
Winbond Serial Flash
EFh
Device ID
(ID7 - ID0)
(ID15 - ID0)
Instruction
ABh, 90h, 92h, 94h
9Fh
W25Q16DW
14h
6015h
相關PDF資料 |
PDF描述 |
|---|---|
| WMF128K8-90FFC5 | 128K X 8 FLASH 5V PROM, 90 ns, CDSO32 |
| WMF128K8-70CLC5 | 128K X 8 FLASH 5V PROM, 70 ns, CQCC32 |
| WS128K64V-20G4WM | 1M X 8 MULTI DEVICE SRAM MODULE, 20 ns, CQMA116 |
| WS512K32-20G2M | 2M X 8 MULTI DEVICE SRAM MODULE, 20 ns, CQFP68 |
| WS512K32F-25G4TM | 2M X 8 MULTI DEVICE SRAM MODULE, 25 ns, QMA68 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| W25Q16DWSFIP | 制造商:WINBOND 制造商全稱:Winbond 功能描述:1.8V 16M-BIT SERIAL FLASH MEMORY WITH DUAL/QUAD SPI & QPI |
| W25Q16DWSNIG | 制造商:WINBOND 制造商全稱:Winbond 功能描述:1.8V 16M-BIT SERIAL FLASH MEMORY WITH DUAL/QUAD SPI & QPI |
| W25Q16DWSNIP | 制造商:WINBOND 制造商全稱:Winbond 功能描述:1.8V 16M-BIT SERIAL FLASH MEMORY WITH DUAL/QUAD SPI & QPI |
| W25Q16DWSSIG | 功能描述:IC FLASH SPI 16MBIT 8SOIC RoHS:是 類別:集成電路 (IC) >> 存儲器 系列:SpiFlash® 標準包裝:2,500 系列:- 格式 - 存儲器:EEPROMs - 串行 存儲器類型:EEPROM 存儲容量:1K (128 x 8) 速度:100kHz 接口:UNI/O?（單線） 電源電壓:1.8 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 封裝/外殼:8-TSSOP，8-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:8-MSOP 包裝:帶卷 (TR) |
| W25Q16DWSSIP | 制造商:WINBOND 制造商全稱:Winbond 功能描述:1.8V 16M-BIT SERIAL FLASH MEMORY WITH DUAL/QUAD SPI & QPI |
發布緊急采購，3分鐘左右您將得到回復。