- 您現在的位置：買賣IC網 > PDF目錄361790 > W742E811 PDF資料下載
參數資料
| 型號： | W742E811 |
| 文件頁數： | 32/66頁 |
| 文件大?。?/td> | 303K |
| 代理商： | W742E811 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁當前第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁
Preliminary W742C(E)811
- 32 -
Note: W means write only.
w
0
1
2
HEF
w
w
w
w
3
4
5
6
7
w
w
w
w
0
HEFD
HEF.0 = 1 Overflow from the Divider 0 causes Hold mode to be released.
HEF.1 = 1 Underflow from Timer 0 causes Hold mode to be released.
HEF.2 = 1 Signal change at port RC causes Hold mode to be released.
HEF.3 = 1 Falling edge signal at port P1.2(
INT0
) causes Hold mode to be released.
HEF.4 = 1 Overflow from the Divider 1 causes Hold mode to be released.
HEF.5 = 1 Serial I/O
HEF.6 = 1 Falling edge signal at port P1.3(
INT1
) causes Hold mode to be released.
HEF.7 = 1 Underflow from Timer 1 causes Hold mode to be released.
HEFD = 1 Signal change at port RD causes Hold mode to be released.
5.15.2 Interrupt Enable Flag (IEF)
The interrupt enable flag is organized as a 8-bit binary register (IEF.0 to IEF.7). These bits are used to
control the interrupt conditions. It is controlled by the MOV IEF, #I instruction. When one of these
interrupts is occurred, the corresponding event flag will be clear, but the other bits are unaffected. In
interrupt subroutine, these interrupts will be disable till the instruction MOV IEF, #I or EN INT is executed
again. However, these interrupts can be disable by executing DIS INT instruction. The bit descriptions
are as follows:
w
1
2
3
IEF
4
w
w
5
6
0
w
w
7
w
w
w
Note: W means write only.
IEF.0 = 1 Interrupt 0 is accepted by overflow from the Divider 0.
IEF.1 = 1 Interrupt 1 is accepted by underflow from the Timer 0.
IEF.2 = 1 Interrupt 2 is accepted by a signal change at port RC.
IEF.3 = 1 Interrupt 3 is accepted by a falling edge signal at port P1.2(
INT0
).
IEF.4 = 1 Interrupt 4 is accepted by overflow from the Divider 1.
IEF.5 = 1 Interrupt 5 is accepted by Serial I/O signal
IEF.6 = 1 Interrupt 6 is accepted by a falling edge signal at port P1.3(
INT1
).
IEF.7 = 1 Interrupt 7 is accepted by underflow from Timer 1.
相關PDF資料 |
PDF描述 |
|---|---|
| W742E | 4-BIT SINGLE-CHIP MICROCONTROLLER FOR SMALL GENERAL-PURPOSE INFRARED REMOTE CONTROL TRANSMITTER |
| W7700A | *****GESTRICHEN***** |
| W7700B | KLEMME FUER FLACHKABEL BIS 40 ADERN |
| W7700C | KLEMME FUER FLACHKABEL BIS 64 ADERN |
| W3435G | LEITERPLATTENSOCKEL TO18/3P 5ST |
相關代理商/技術參數 |
參數描述 |
|---|---|
| W742E813 | 制造商:WINBOND 制造商全稱:Winbond 功能描述:4-BIT MICROCONTROLLER |
| W742E816 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Microcontroller |
| W742E81A | 制造商:WINBOND 制造商全稱:Winbond 功能描述:4-BIT MICROCONTROLLER |
| W742S819 | 制造商:WINBOND 制造商全稱:Winbond 功能描述:4-BIT TELEPHONE CONTROLLER |
| W742S81A | 制造商:WINBOND 制造商全稱:Winbond 功能描述:4 BIT MICROCONTROLLER |
發布緊急采購，3分鐘左右您將得到回復。