- 您現在的位置：買賣IC網 > PDF目錄1974 > XCCACE-TQG144I (Xilinx Inc)IC ACE CONTROLLER CHIP TQ144 PDF資料下載
參數資料
| 型號： | XCCACE-TQG144I |
| 廠商： | Xilinx Inc |
| 文件頁數： | 2/69頁 |
| 文件大小： | 0K |
| 描述： | IC ACE CONTROLLER CHIP TQ144 |
| 產品變化通告： | XCCACE-TQG144I Discontinuation 31/Oct/2011 |
| 標準包裝： | 60 |
| 控制器類型： | ACE 控制器 |
| 電源電壓： | 3 V ~ 3.6 V |
| 電流 - 電源： | 30mA |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 144-LQFP |
| 供應商設備封裝： | 144-TQFP（20x20） |
| 包裝： | 管件 |
| 其它名稱： | 122-1511-5 |
第1頁當前第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁
System ACE CompactFlash Solution
10
DS080 (v3.0) April 7, 2014
Product Specification
R
— OBSOLETE — OBSOLETE — OBSOLETE — OBSOLETE —
System ACE CF File Structure Requirements
The System ACE CF file structure must be on the first
partition of the CompactFlash device.
The System ACE CF partition must be formatted as
DOS FAT12 or FAT16.
The xilinx.sys file or single ACE file must be in
the root directory. The ACE file used only if
xilinx.sys
is not found. The xilinx.sys file
describes one collection directory with up to eight
subdirectories.
The xilinx.sys file must contain the line
dir=<dir_name>; where <dir_name> is the name of the
collection directory
The subsequent 8 lines of the xilinx.sys file must
consist of the lines cfgaddr<n>=<subdir_name>; where
<n> is 1 through 8 and <subdir_name> is the name of
a design sub-directory in the collection. In the case of
fewer than 8 designs in the collection, always start with
cfgaddr0 and only use contiguous cfgaddr locations.
Only one ACE file should exist in the ROOT directory
and/or in each \<dir>\<cfgaddr> folder pointed to
by the xilinx.sys file.
When sourcing from the MPU, the total length of the
ACE file must be a multiple of 32 bytes. Otherwise,
additional dummy bytes (1s or 0s) should be sent to
DATABUFREG to flush the last data buffer, allowing the
controller to correctly load the final commands in the
ACE file.
All directories accessed by the System ACE CF
controller must be formatted in a valid FAT 8.3 file
name format.
ACE file names can be up to eight characters long and
must include the .ace file extension.
All directories and ACE file names cannot contain
these reserved characters:
left angle bracket
<
right angle bracket
>
colon
:
quote mark
"
forward slash
/
back slash
\
pipe
|
The Partition Boot Record (PBR) for the first
CompactFlash partition that is used by the System
ACE CF controller must specify only one reserved
sector.
The CompactFlash card must be formatted with a
sector-per-cluster size greater than 1.
Other files and directories can coexist with System
ACE files and directories.
2 GB is the maximum capacity partition that the
System ACE CF controller can access using the FAT16
file system:
(65,535 clusters max) X (32 KB per cluster max)
= 2,147,123,200 bytes
2GB
16 MB is the maximum capacity partition that the
System ACE CF controller can access using the FAT12
file system:
(4,086 clusters max) X (4 KB per cluster max)
= 16,736,256 bytes
16 MB
System ACE CF Formatting Requirements
Three potential problem areas arise when formatting the CF
card for use with the System ACE CF controller:
1.
Sectors-per-Cluster Size
A CF card formatted with only one sector (512 bytes)
per cluster can cause problems for the System ACE CF
controller.
When the Windows OS formats the CF card, it uses a
formula to determine what it believes to be an optimal
sectors-per-cluster value, based on the size of the CF
partition and other factors. This can lead some
Windows OS versions to specify one sector (512 bytes)
per cluster in some CF configurations. For example, this
situation is known to occur when formatting 32 MB CF
cards with Windows 2000 and Windows XP. Disk
formatting utilities (such as mkdosfs, available from
http://www1.mager.org/mkdosfs) can be used to
avoid this situation.
2.
FAT12 or FAT16 Format
The System ACE CF controller does not recognize the
FAT32 file system. It was designed to recognize only the
FAT12 and FAT16 formats.
3.
Reserved Sectors
Reserved sectors are the sectors in the reserved region
of the volume starting at the first sector of the volume.
The System ACE CF controller can only read a CF card
that is formatted with one reserved sector in the
Partition Boot Record.
Specifying Sectors-per-Cluster and FAT Version
To correct the first two of these formatting issues, the CF
card should always be formatted with a sectors-per-cluster
size greater than 1 (UnitSize greater than 512), and the FAT
file system version should be specified. This can be done
using the format command with the
/fs:
and
/a:
options in this syntax:
format <volume> [/fs:<FileSystem>]
[/a:<UnitSize>]
For example:
format D: /FS:FAT /A:1024
相關PDF資料 |
PDF描述 |
|---|---|
| XCF128XFTG64C | IC PROM SRL 128M GATE 64-FTBGA |
| XCF32PFS48C | IC PROM SRL 1.8V 32M 48CSBGA |
| XCR3256XL-7CS280C | IC CPLD 256MCELL 3.3V HP 280CSP |
| XCS10-3VQG100C | IC FPGA 5V C-TEMP 100-VQFP |
| XCV600E-8HQ240C | IC FPGA 1.8V C-TEMP 240-HQFP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XCCAE7C13N | 制造商:Schneider Electric 功能描述:ABSOLUTE ENCDER SINGLE TURN 13 BITS 11 30V DC 制造商:SCHNEIDER ELECTRIC 功能描述:ABSOLUTE ENCDER SINGLE TURN |
| XCC-C0 | 制造商:Excelsys Technologies 功能描述:ELECTRONIC PART |
| XCCN0000 | 制造商:Red Lion Controls 功能描述:OPTION CARD, DSP/MC CANOPEN OPTION CARD 制造商:Red Lion Controls 功能描述:DSP/MC CANOPEN OPTION CARD |
| XCCPM23121L10 | 制造商:Schneider Electric 功能描述:pre-wired M23 female connector - for incremental encoder - cable 10m 制造商:Schneider Electric 功能描述:Cable Assembly Pre-Wired Pigtail 10m 10 POS M23 Circular F |
| XCCPM23121L2 | 制造商:Schneider Electric 功能描述:PRE WIRED CONNECTOR M23 10 WIRES INCREM 2M 制造商:SCHNEIDER ELECTRIC 功能描述:Cable Assembly 2m 10 POS M23 Circular |
發布緊急采購，3分鐘左右您將得到回復。