REV. 1.4.2 SMALLEST 2.25V TO 5.5V UART WITH 16-BYTE FIFO AND POWERSAVE 4.4.2 IER versus Receive/Transmit FIFO Polled Mode Operation" />
參數資料
型號: XR16L580IL-F
廠商: Exar Corporation
文件頁數: 18/49頁
文件大?。?/td> 0K
描述: IC UART FIFO 16BYTE 32QFN
標準包裝: 490
通道數: 1,UART
FIFO's: 16 字節
規程: RS232,RS422
電源電壓: 2.25 V ~ 5.5 V
帶自動流量控制功能:
帶IrDA 編碼器/解碼器:
帶故障啟動位檢測功能:
帶調制解調器控制功能:
帶CMOS:
安裝類型: 表面貼裝
封裝/外殼: 32-VFQFN 裸露焊盤
供應商設備封裝: 32-QFN(5x5)
包裝: 托盤
其它名稱: 1016-1423
XR16L580
25
REV. 1.4.2
SMALLEST 2.25V TO 5.5V UART WITH 16-BYTE FIFO AND POWERSAVE
4.4.2
IER versus Receive/Transmit FIFO Polled Mode Operation
When FCR bit-0 equals a logic 1 for FIFO enable; resetting IER bits 0-3 enables the XR16L580 in the FIFO
polled mode of operation. Since the receiver and transmitter have separate bits in the LSR either or both can
be used in the polled mode by selecting respective transmit or receive control bit(s).
A. LSR BIT-0 indicates there is data in RHR or RX FIFO.
B. LSR BIT-1 indicates an overrun error has occurred and that data in the FIFO may not be valid.
C. LSR BIT 2-4 provides the type of receive data errors encountered for the data byte in RHR, if any.
D. LSR BIT-5 indicates THR is empty.
E. LSR BIT-6 indicates when both the transmit FIFO and TSR are empty.
F. LSR BIT-7 indicates a data error in at least one character in the RX FIFO.
IER[0]: RHR Interrupt Enable
The receive data ready interrupt will be issued when RHR has a data character in the non-FIFO mode or when
the receive FIFO has reached the programmed trigger level in the FIFO mode.
Logic 0 = Disable the receive data ready interrupt (default).
Logic 1 = Enable the receiver data ready interrupt.
IER[1]: THR Interrupt Enable
This bit enables the Transmit Ready interrupt which is issued whenever the THR becomes empty in the non-
FIFO mode or when data in the FIFO falls below the programmed trigger level in the FIFO mode. If the THR is
empty when this bit is enabled, an interrupt will be generated.
Logic 0 = Disable Transmit Ready interrupt (default).
Logic 1 = Enable Transmit Ready interrupt.
IER[2]: Receive Line Status Interrupt Enable
If any of the LSR register bits 1, 2, 3 or 4 is a logic 1, it will generate an interrupt to inform the host controller
about the error status of the current data byte in FIFO. LSR bit-1 generates an interrupt immediately when the
character has been received. LSR bits 2-4 generate an interrupt when the character with errors is read out of
the FIFO.
Logic 0 = Disable the receiver line status interrupt (default).
Logic 1 = Enable the receiver line status interrupt.
IER[3]: Modem Status Interrupt Enable
Logic 0 = Disable the modem status register interrupt (default).
Logic 1 = Enable the modem status register interrupt.
IER[4]: Sleep Mode Enable (requires EFR bit-4 = 1)
Logic 0 = Disable Sleep Mode (default).
Logic 1 = Enable Sleep Mode. See Sleep Mode section for further details.
IER[5]: Xoff Interrupt Enable (requires EFR bit-4=1)
Logic 0 = Disable the software flow control, receive Xoff interrupt. (default)
Logic 1 = Enable the software flow control, receive Xoff interrupt. See Software Flow Control section for
details.
相關PDF資料
PDF描述
XR16M681IL24-F IC UART FIFO 64B 24QFN
XR16M681IB25-F IC UART FIFO 64B 25BGA
ST16C550IJ44-F IC UART FIFO 16B SGL 44PLCC
ST16C450IQ48-F IC UART SINGLE 48TQFP
MAX7324AEG+T IC I/O EXPANDER I2C 8B 24QSOP
相關代理商/技術參數
參數描述
XR16L580IL-F 制造商:Exar Corporation 功能描述:IC SGL UART 3MBPS 5.5V 32-QFN
XR16L580ILTR 功能描述:UART 接口集成電路 UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
XR16L580ILTR-F 功能描述:UART 接口集成電路 UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
XR16L580IM 制造商:EXAR 制造商全稱:EXAR 功能描述:SMALLEST 2.25V TO 5.5V UART WITH 16-BYTE FIFO AND POWERSAVE
XR16L580IM-0A-EVB 功能描述:UART 接口集成電路 Supports L580 48 ld TQFP, ISA Interface RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel