REV. 1.4.2 2.12 Auto RTS (Hardware) Flow Control This " />
參數資料
型號: XR16L580IL-F
廠商: Exar Corporation
文件頁數: 8/49頁
文件大?。?/td> 0K
描述: IC UART FIFO 16BYTE 32QFN
標準包裝: 490
通道數: 1,UART
FIFO's: 16 字節
規程: RS232,RS422
電源電壓: 2.25 V ~ 5.5 V
帶自動流量控制功能:
帶IrDA 編碼器/解碼器:
帶故障啟動位檢測功能:
帶調制解調器控制功能:
帶CMOS:
安裝類型: 表面貼裝
封裝/外殼: 32-VFQFN 裸露焊盤
供應商設備封裝: 32-QFN(5x5)
包裝: 托盤
其它名稱: 1016-1423
XR16L580
16
SMALLEST 2.25V TO 5.5V UART WITH 16-BYTE FIFO AND POWERSAVE
REV. 1.4.2
2.12
Auto RTS (Hardware) Flow Control
This feature is not available in the 24-QFN package since it does not have the RTS# pin.
Automatic RTS hardware flow control is used to prevent data overrun to the local receiver FIFO. The RTS#
output is used to request remote unit to suspend/resume data transmission. The auto RTS flow control
features is enabled to fit specific application requirement (see
Enable auto RTS flow control using EFR bit-6.
The auto RTS function must be started by asserting RTS# output pin (MCR bit-1 to logic 1 after it is enabled).
If using the Auto RTS interrupt:
Enable RTS interrupt through IER bit-6 (after setting EFR bit-4). The UART issues an interrupt when the
RTS# pin makes a transition from low to high: ISR bit-5 will be set to logic 1.
2.13
Auto RTS Hysteresis
The L580 has a new feature that provides flow control trigger hysteresis while maintaining compatibility with
the ST16C550 UART. With the Auto RTS function enabled, an interrupt is generated when the receive FIFO
reaches the programmed RX trigger level. The RTS# pin will not be forced to a logic 1 (RTS off), until the
receive FIFO reaches one trigger level above the programmed trigger level in the trigger table (
Table 8). The
RTS# pin will return to a logic 0 after the RX FIFO is unloaded to one trigger level lower than the programmed
trigger level. This is described in
Figure 11. Under the above described conditions, the L580 will continue to
accept data until the receive FIFO gets full. The Auto RTS function is initiated when the RTS# output pin is
asserted to a logic 0 (RTS On).
2.14
Auto CTS Flow Control
This feature is not available in the 24-QFN package since it does not have the CTS# pin.
Automatic CTS flow control is used to prevent data overrun to the remote receiver FIFO. The CTS# input is
monitored to suspend/restart the local transmitter. The auto CTS flow control feature is selected to fit specific
application requirement (see
Enable auto CTS flow control using EFR bit-7.
If using the Auto CTS interrupt:
Enable CTS interrupt through IER bit-7 (after setting EFR bit-4). The UART issues an interrupt when the
CTS# pin is de-asserted (HIGH): ISR bit-5 will be set to 1, and UART will suspend transmission as soon as
the stop bit of the character in process is shifted out. Transmission is resumed after the CTS# input is re-
asserted (LOW), indicating more data may be sent.
相關PDF資料
PDF描述
XR16M681IL24-F IC UART FIFO 64B 24QFN
XR16M681IB25-F IC UART FIFO 64B 25BGA
ST16C550IJ44-F IC UART FIFO 16B SGL 44PLCC
ST16C450IQ48-F IC UART SINGLE 48TQFP
MAX7324AEG+T IC I/O EXPANDER I2C 8B 24QSOP
相關代理商/技術參數
參數描述
XR16L580IL-F 制造商:Exar Corporation 功能描述:IC SGL UART 3MBPS 5.5V 32-QFN
XR16L580ILTR 功能描述:UART 接口集成電路 UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
XR16L580ILTR-F 功能描述:UART 接口集成電路 UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
XR16L580IM 制造商:EXAR 制造商全稱:EXAR 功能描述:SMALLEST 2.25V TO 5.5V UART WITH 16-BYTE FIFO AND POWERSAVE
XR16L580IM-0A-EVB 功能描述:UART 接口集成電路 Supports L580 48 ld TQFP, ISA Interface RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel