xr
TWO CHANNEL DS3/E3 FRAMER IC WITH HDLC CONTROLLER
XRT72L52
REV. 1.0.1
67
2.3.3.5
Receive E3 Interrupt Status Register 1 (E3, ITU-T G.832)
Bit 6 - SSM Message Interrupt Status
This Reset-upon-Read bit-field indicates whether or not a Change of Synchronization Status Message (SSM)
Interrupt has occurred since the last read of this register. This interrupt will occur whenever a change in the
contents of the SSM (within the inbound E3 data stream) has been detected.
If this bit-field has been set to “1”, then the Change of SSM Interrupt has occurred since the last read of this
register. Conversely, if this bit-field has been set to “0”, then the Change of SSM Interrupt has not occurred
since the last read of this register.
N
OTE
:
This bit-field is invalid if the channel has been configured to support the November 1995 revision of the ITU-T G.832
Framing format for E3.
Bit 5 - SSM Out of Sequence Interrupt Status
This Reset-upon-Read bit-field indicates whether or not the Change in SSM Out of Sequence State interrupt
has occurred since the last read of this register. This interrupt will occur in response to either of the following
conditions.
1.
The Receive Section losses sequence synchronization with the SSM data.
2.
The Receive Section re-acquires sequence synchronization with the SSM data.
N
OTE
:
This bit-field is invalid if the Channel has been configured to support the November 1995 revision of the ITU-T G.832
Framing format for E3.
Bit 4 - COFA (Change of Frame Alignment) Interrupt Status
This Reset-upon-Read bit-field will be set to "1" if the Change of Frame Alignment interrupt has occurred since
the last read of this register.
The Receive DS3/E3 Framer block will generate the Change of Frame Alignment interrupt if it has detected a
change in frame alignment in the incoming E3 frames.
Bit 3 - OOF (Receive E3 Framer) Interrupt Status
This Reset Upon Read bit-field is set to "1" if the Receive DS3/E3 Framer block has detected a Change in the
Out-of-Frame (OOF) Condition, since the last time this register was read. Therefore, this bit-field will be as-
serted under either of the following two conditions:
1.
When the Receive DS3/E3 Framer block has detected the appropriate conditions to declare an OOF Con-
dition.
2.
When the Receive DS3/E3 Framer block has transitioned from the OOF Condition (Frame Acquisition
Mode) into the In-Frame Condition (Frame Maintenance mode).
N
OTE
:
For more information of the OOF Condition, refer to
Section 6.3.2.1
.
Bit 2 - LOF (Loss of Frame) Interrupt Status
This Reset-upon-Read bit-field will be set to "1" if a Change in LOF Condition interrupt has occurred since the
last read of this register.
The Receive DS3/E3 Framer block will generate the Change in LOF Condition interrupt in response to either of
the following two occurrences.
1.
Whenever the Receive DS3/E3 Framer block transitions from the OOF Condition state into the LOF Condi-
tion state, within the E3 Framing Acquisition/Maintenance algorithm (per
Figure 182
).
RXE3 INTERRUPT STATUS REGISTER 1 (ADDRESS = 0X14)
B
IT
7
B
IT
6
B
IT
5
B
IT
4
B
IT
3
B
IT
2
B
IT
1
B
IT
0
Not Used
SSM MSG
Interrupt
Status
SSM OOS
Interrupt
Status
COFA
Interrupt
Status
OOF
Interrupt
Status
LOF
Interrupt
Status
LOS
Interrupt
Status
AIS
Interrupt
Status
RO
RUR
RUR
RUR
RUR
RUR
RUR
RUR
0
0
0
0
0
0
0
0