PIN # <" />
參數資料
型號： XRT73LC00AIV
廠商： Exar Corporation
文件頁數： 59/61頁
文件大?。?/td> 0K
描述： IC LIU STS1/DS3/E3 SGL 44TQFP
標準包裝： 160
類型： 線路接口裝置（LIU）
驅動器/接收器數： 1/1
規程： DS3，E3，STS-1
電源電壓： 3.135 V ~ 3.465 V
安裝類型： 表面貼裝
封裝/外殼： 44-LQFP
供應商設備封裝： 44-TQFP（10x10）
包裝： 托盤
XRT73LC00A
4
REV. 1.0.2
E3/DS3/STS-1 LINE INTERFACE UNIT
PIN DESCRIPTION
PIN #
SYMBOL
TYPE
DESCRIPTION
1
TXLEV
I
Transmit Line Build-Out Enable/Disable Select:
This input pin is used to enable or disable the Transmit Line Build-Out circuit in
the XRT73LC00A.
Setting this pin to “High” disables the Line Build-Out circuit. In this mode, the
XRT73LC00A outputs partially shaped pulses onto the line via the TTIP and
TRING output pins.
Setting this pin to “Low” enables the Line Build-Out circuit. In this mode, the
XRT73LC00A outputs partially-shaped pulses onto the line via the TTIP and
TRING output pins.
To comply with the isolated DSX-3/STSX-1 Pulse Template Requirements per
Bellcore GR-499-Core or Bellcore GR-253-Core:
1. Set this input pin to a "1" if the cable length between the Cross-Connect and
the transmit output of the XRT73LC00A is greater than 225 feet.
2. Set this input pin to a "0" if the cable length between the Cross-Connect and
the transmit output of the XRT73LC00A is less than 225 feet.
This pin is active only if both of the following are true:
(a) The XRT73LC00A is configured to operate in either the DS3 or SONET
STS-1 modes and
(b) The XRT73LC00A is configured to operate in the Hardware Mode.
NOTE: This pin should be tied to GND if the XRT73LC00A is to be operated in
the HOST mode.
2
TAOS
I
Transmit All Ones Select:
A “High” on this pin causes a continuous AMI all “1’s” pattern to be transmitted
onto the line. The frequency of this “1’s” pattern is determined by TCLK.
NOTES:
1.
This input pin is ignored if the XRT73LC00A is operating in the HOST
Mode.
2.
Tie this pin to GND if the XRT73LC00A is going to be operating in the
HOST Mode.
3
TxAVDD
****
Transmit Analog Power Supply
4
DMO
O
Drive Monitor Output:
If no bipolar line signal is detected on the TTIP/TRING output pins via the MTIP
and MRING input pins for 128±32 TCLK periods, then the DMO output pin tog-
gles and remains “High” until the next bipolar pulse is detected.
5
TxAGND
****
Transmit Analog Ground
6
AGND
****
Analog Ground (Substrate)
7
RxAGND
****
Receive Analog Ground
8
RTIP
I
Receive TIP Input:
This input pin along with RRING is used to receive the line signal from the
Remote DS3/E3/STS-1 Terminal.
9
RRING
I
Receive RING Input:
This input pin along with RTIP is used to receive the line signal from the Remote
DS3/E3/STS-1 Terminal.
10
RxAVDD
****
Receive Analog Power Supply
相關PDF資料
PDF描述
VI-B4Y-IU-F1 CONVERTER MOD DC/DC 3.3V 132W
ISL26708IHZ-T IC ADC 8BIT SPI/SRL 1M 8-SOT-23
VI-B4X-IV-F3 CONVERTER MOD DC/DC 5.2V 150W
XRT75VL00IV IC LIU E3/DS3/STS-1 1CH 52TQFP
ISL26310FBZ-T IC ADC 12BIT SPI/SRL 125K 8SOIC
相關代理商/技術參數
參數描述
XRT73LC00AIV-F 功能描述:外圍驅動器與原件 - PCI 1-Ch DS3, E3, SONET RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray
XRT73LC00AIVTR 功能描述:網絡控制器與處理器 IC RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
XRT73LC00AIVTR-F 功能描述:網絡控制器與處理器 IC RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
XRT73LC00IV 制造商:EXAR 制造商全稱:EXAR 功能描述:E3/DS3/STS-1 LINE INTERFACE UNIT
XRT73LC03A 制造商:EXAR 制造商全稱:EXAR 功能描述:3 CHANNEL DS3/E3/STS-1 LINE INTERFACE UNIT
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*