參數資料
型號： XRT75L00D
廠商： Exar Corporation
英文描述： E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER
中文描述： E3/DS3/STS-1線路接口單元與SONET DESYNCHRONIZER
文件頁數： 11/92頁
文件大?。?/td> 894K
代理商： XRT75L00D
XRT75L00D
REV. 1.0.2
E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER
6
RECEIVE INTERFACE
P
IN
#
S
IGNAL
N
AME
T
YPE
D
ESCRIPTION
25
RxON/
SDI
I
Receiver Turn ON Input or Serial Data Input:
Function of this pin depends on whether the XRT75L00D is configured to oper-
ate in Hardware mode or Host mode.
In Hardware mode, setting this input pin “High” turns on and enables the
Receiver..
N
OTES
:
1.
If the XRT75L00D is configured in HOST mode, this pin functions as
SDI input pin (please refer to the pin description for Microprocessor
Interface)
2.
This pin is internally pulled down.
23
REQEN
I
Receive Equalization Enable Input
Setting this input pin "High" enables the Internal Receive Equalizer. Setting this
pin "Low" disables the Internal Receive Equalizer.
N
OTES
:
1.
This input pin is ignored and may be connected to GND if the
XRT75L00D is operating in the HOST Mode
2.
This pin is internally pulled down.
36
RxClk
O
Receive Clock Output
The Recovered Clock signal from the incoming line signal is output through this
pin.By default, the Receiver Section outputs data via RPOS and RNEG pins on
the rising edge of this clock signal.
Configure the Receiver Section to update data on the RPOS and RNEG pins on
the falling edge of RxClk by doing the following:
a)
Operating in Hardware mode
, pull the RxClkINV pin to “High”.
b)
Operating in Host mode
, write a “1” to RxClkINV bit field within the Receive
Control Register.
24
RxClkINV/
CS
I
RxClk INVERT or Chip Select
:
Function of this pin depends on whether the XRT75L00D is configured to oper-
ate in Hardware mode or Host mode.
In Hardware mode, setting this input pin “High” configures the Receiver Sec-
tion to invert the RxClk output signals and outputs the recovered data via
RPOS and RNEG on the falling edge of RxClk.
N
OTE
:
If the XRT75L00D is configured in HOST mode, this pin functions as CS
input pin (please refer to the pin description for Microprocessor
Interface).
38
RPOS
O
Receive Positive Data Output
This output pin pulses “High" whenever the XRT75L00D has received a Posi-
tive Polarity pulse in the incoming line signal at the RTIP/RRing inputs.
相關PDF資料
PDF描述
XRT75L00DIV E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER
XRT75L02 TWO CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH JITTER
XRT75L02IV TWO CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH JITTER
XRT75L03D THREE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER
XRT75L04D FOUR CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER
相關代理商/技術參數
參數描述
XRT75L00DES 功能描述:時鐘合成器/抖動清除器 LIU+DESYNCH 3.3V LIU+DESYNCH 3.3V RoHS:否 制造商:Skyworks Solutions, Inc. 輸出端數量: 輸出電平: 最大輸出頻率: 輸入電平: 最大輸入頻率:6.1 GHz 電源電壓-最大:3.3 V 電源電壓-最小:2.7 V 封裝 / 箱體:TSSOP-28 封裝:Reel
XRT75L00DIV 功能描述:外圍驅動器與原件 - PCI 3.3V 1 CH E3/DS3/STS W/SONET DE-SYNCH RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray
XRT75L00DIV-F 功能描述:外圍驅動器與原件 - PCI 1-Ch DS3, E3, SONET RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray
XRT75L00DIVTR 功能描述:時鐘合成器/抖動清除器 3.3V 1 CH E3/DS3/STS W/SONET DE-SYNCH RoHS:否 制造商:Skyworks Solutions, Inc. 輸出端數量: 輸出電平: 最大輸出頻率: 輸入電平: 最大輸入頻率:6.1 GHz 電源電壓-最大:3.3 V 電源電壓-最小:2.7 V 封裝 / 箱體:TSSOP-28 封裝:Reel
XRT75L00DIVTR-F 功能描述:時鐘合成器/抖動清除器 3.3V 1 CH E3/DS3/STS W/SONET DE-SYNCH RoHS:否 制造商:Skyworks Solutions, Inc. 輸出端數量: 輸出電平: 最大輸出頻率: 輸入電平: 最大輸入頻率:6.1 GHz 電源電壓-最大:3.3 V 電源電壓-最小:2.7 V 封裝 / 箱體:TSSOP-28 封裝:Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*